I am using a stock 2016 lt1 with an 8l90e trans (t87). All the operating systems are from the donor vehicle. The problem I am having is when the Accelerator pedal is depressed the scanner reads 99%...
Type: Posts; User: owens1
I am using a stock 2016 lt1 with an 8l90e trans (t87). All the operating systems are from the donor vehicle. The problem I am having is when the Accelerator pedal is depressed the scanner reads 99%...
Working on 2015 silverado not going into PE. The commanded AFR stays at 14.11. Occasionally PE will engage above 4000 RPMs. Anyone had an issue like this?
Cannot remove rev limiter on 1999 corvette. no matter where I put the fuel cut offs, at around 7600 the engine goes into spark induced rev limit. Possible built in limiter like the black box ecms? ...
Installed 3.73 gears and 30 inch tires on 2007 silverado and calibrated through the wizard. Now I have and abs/brake lamp illuminated and the front and rear wheel speeds are different. Any help...
Having problems with the 1-2 shift on a 1999 corvette. The car has a 250 shot of nitrous and a built trans. When the engine is up to operating temp but not driven to warm the trans it runs through...
Why does some of the files opened with 3.0 show tire adjustments in circumference and others in height?
Tried to read a black ecm on a 1999 Tahoe, but was unable to complete. The vehicle is still on the supported list. Anyone else had issue with this?
I am probably missing something, but how do you load tables into the vcm scanner graphs that matches the editor?
So if I rename the cfg files in setting I can still use 2.24 along with 3.0?
Since I downloaded 2.25 beta I see there is no longer a parameter for entering gear and tire size. Is there something I'm missing or do the math manually.
What exactly does the etc injector disable parameter do?
I am trying to dial in final min airflow on an 07 trailblazer. Is the proper way to just log the maf g/s into the table and adjust?
Low desired airflow can be caused by large hole in throttle blade, or iac vs effective area table may need to be adjusted, especially if it has a larger TB.
I am using a 2000 Silverado ecm. I don't see any modifiers for garage shifts.
I installed a 4l60e behind a cammed ls2 and now have hard garage shifts most of the time. I have already raised the 0 column in the pcs table, which helped but is still a little firm. Are there any...
When I am logging AFR error on a wot pull the first few cells after the transition from closed to wot always end up way lean. Is this normal or is there a filter that needs to added to the...
I contacted support about a certain table not being available in the OS of an f-body. They told me it was now available in latest build, but I cannot download. I receive the message:
Not...
Any way to have it added, or do I have to change the OS?
The OS is 9381344, but I had a segment swap done.
I have version 2.24.684, but I don't have the D1 table is there something missing?
I cannot manually hold 1st gear in my 4l80. I have installed transgo hd2 kit but it still does the same, found out that the later kits deleted this function. Is there a table in htp to raise or...
I have pull every fuse I have read about and I went as far as to isolate the ecm and tcm on the data bus. I am also using 2.24.648
I still haven't got it figured out. Quit working on it since it is my personal truck. Still would like to know. It still times out after a few seconds of trying read the tcm.
I still haven't got the tcm to stop timing out. I have got the latest beta software installed and disconnected all modules, but the tcm and the ecm from the data bus. Tried high and low speed...
I have yet to be able to read the tcm on this 2005 lly. Any suggestions. I don't have an older beta, is there any way to download one to try?