Search:

Type: Posts; User: fast5ooh

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    2,623

    thanks @blindsquirrel , i will give that a shot...

    thanks @blindsquirrel , i will give that a shot and see if that changes anything.

    I think i am going to get out of SD mode and tighten up the MAF tuning to see if that helps with the idle.
  2. Replies
    15
    Views
    2,623

    Yes they are.. i re-verified the file as well and...

    Yes they are.. i re-verified the file as well and that is where i am pulling the data from, the 660cc data. I mentioned above, the data exceeds the HP tuners flow rate vs pressure. The only way it...
  3. Replies
    15
    Views
    2,623

    I don't remember changing the ITT, so you may be...

    I don't remember changing the ITT, so you may be correct. I will verify the stock base tune.

    It's a spec cam from Greg good but cut by Texas speed. If I had to estimate, it would be the similar to...
  4. Replies
    15
    Views
    2,623

    And by the way, since doubled the stoich AFR, i...

    And by the way, since doubled the stoich AFR, i cut the flow rate data in half to compensate.. so thats why you see a 50% deviation in the injector flow rate data.
  5. Replies
    15
    Views
    2,623

    I got the data from Fuel injector clinic.. they...

    I got the data from Fuel injector clinic.. they provide very accurate injector data
  6. Replies
    15
    Views
    2,623

    Full top end 103 tb - etc scalar set to 1780...

    Full top end
    103 tb - etc scalar set to 1780
    Ls7 heads Frankenstein ported
    Greg good cam
    MSD atomic intake Tony Mamo ported -manifold volume roughly set to 11,3~~
    72 lb injectors
    And all...
  7. Replies
    15
    Views
    2,623

    Minor VE change - Car wont idle -ITT zeroed

    Hey Guys,

    I have come to a point where my car idles half way decent (surges a bit till i blip the throttle and it returns).. But still Tuning in SD mode with MAF disabled and verified that the...
  8. Hey Smokeshow, I am running in speed density...

    Hey Smokeshow,

    I am running in speed density as i am still fine tuning the VE table.

    When i had the MAF enabled, it ran so bad that the car wouldnt even drive down the block without going into...
  9. e38 ls7 - bucking at ~1500 rpm timing erratic

    Hey Guys,

    I have been doing a lot of VE table refining and have the car driving and somewhat idling decently after doing a whole top end.

    I looked at my base timing tables high/low octane are...
  10. e38 ls7 - full top end - 72lb injectors - barely runs - tune & log file inc.

    Hey Guys,

    So i am still learning all the ins and outs of tuning. I see 50/50 responses on MAF and Speed Density, and now i have a HUGE issue with getting the car to idle with 72lb injectors and...
  11. Replies
    6
    Views
    2,063

    thank you guys for the feedback! I think i...

    thank you guys for the feedback!

    I think i am going to pull the trigger and not look back and do the 2 bar map OS patch.
  12. Replies
    6
    Views
    2,063

    Speed Density on E38 - 07 C6 Z06

    Hey Guys,

    i am beginning my tuning experience with my c6 z06.

    Just put the following together:

    Frankenstein Ls7 Ported Heads
    Greg Good HPC Hulk LS7 cam
    Mamo Ported MSD
    Katech 103mm TB
Results 1 to 12 of 12