EEC-V Support

[jr2185]

What will need to get the beta just purchase the mpvi3 ?

The beta software is on the downloads page on their website.

[Neelix66]

Hi Eric, is it possible to get the latest EECV firmware for RTD so it can be used with the RTD flasher?

[BWebb]

I?m currently on the fence about converting my 86 fs bronco eecIV to an explorer EECV if there was full support for all 95-01 explorers. Don?t want to buy an external tranny controller and a separate engine control system. Maybe I missed it in this thread but are all 95-01 exploders covered now?

[Outlawz177]

This.

So i purchased mpvi3 and downloaded beta it says failed then down below says interface not supported
what do i do ?

[rico360z28]

Today's build has support for 2003-2004 Mercury Marauder 4.6L 4V

Great!! How do I get newer builds? besides whats in production?

[jr2185]

Do you have the beta software? If so, open it and go to help - about and check for updates.

[jr2185]

So i purchased mpvi3 and downloaded beta it says failed then down below says interface not supported
what do i do ?

When does it say it failed? Did you request the EEC-V firmware?

[Outlawz177]

When does it say it failed? Did you request the EEC-V firmware?

Yes I have the beta version download where do you request for the EEC-v firmware?

[Bill@HPTuners]

Yes I have the beta version download where do you request for the EEC-v firmware?

via support ticket is your best bet.

[BWebb]

Are all 95-01 5.0 explorers covered now?

[Outlawz177]

I have dumb question on the 1999-2004 Mustang what timing selection to use for adding timing mainly wot I think it could use a couple degrees . On these there is not a high octane map I can see .

[Eric@HPTuners]

I have dumb question on the 1999-2004 Mustang what timing selection to use for adding timing mainly wot I think it could use a couple degrees . On these there is not a high octane map I can see .

Borderline Knock is generally what you use to set the timing. However if MBT is lower than what you request, it will clip to that value.

[Eric@HPTuners]

Are all 95-01 5.0 explorers covered now?

No, not all REAC3 and REAC4 strategies only currently (10.15.24)

[Truedeal]

Ok , on the mpvi3 supported applications it still says that eecv is not supported in any capacity.

Is this still the case or can I now buy a MPVI3 to tune a 03 Terminator?

[Eric@HPTuners]

Ok , on the mpvi3 supported applications it still says that eecv is not supported in any capacity.

Is this still the case or can I now buy a MPVI3 to tune a 03 Terminator?

Out of the box, if you hook up an MPVI3 to any EEC, it will tell you not supported until you get the EEC specific firmware.

[LUKAS98]

Hi Eric,

possible to add this?

KQTH7D2_OEM.hpt

[Bill@HPTuners]

Hi Eric,

possible to add this?

KQTH7D2_OEM.hpt

For tracking purposes would you be able to open a support ticket? We'd really prefer all of the new definitions to go through the proper channels.

[LUKAS98]

why open support ticket, if i have no response ?

i have do it for another def files like KQAH3T4, no answer...


what do you think about this ?kqah3T4.jpg

[Bill@HPTuners]

Your ford Focus definition is already in Eric's work in queue and we did respond as you can see in your screenshot.

[Eric@HPTuners]

why open support ticket, if i have no response ?

i have do it for another def files like KQAH3T4, no answer...


what do you think about this ?kqah3T4.jpg

I'll get to it soon. I did probably 5 EEC-V definitions this week.