18 ss camaro throttle close

[Jmarkum5]

tony datalog3.hpltony datalog2.hpl

[Jmarkum5]

Any one help out please ����

[04silverado6.0]

You have managed to not provide any info on the car, not included a tune, did not log any torque channels in the scanner. The only advice i can give is double check driver demand, vve, vtt. Should have a channel named throttle source or torque source you can add in.

[discussvolatile]

Sorry but I can't read your file. Can you please post the specific problem here?

[Alvin]

There can be several reasons for this. Post your tune file and we will have a look.

[TriPinTaZ]

we really need a sticky in here that posts up a general channel config and requirements to include in creating a thread asking for help.

[edcmat-l1]

businessman-looking-into-crystal-ball.jpg

Y'all just need one a these!!

[Jmarkum5]

There can be several reasons for this. Post your tune file and we will have a look.

021425_Trans_6400_Test_2jd.hpt021425_Trans_6400_Test_2jd.hpt

[Jmarkum5]

There can be several reasons for this. Post your tune file and we will have a look.

i sent file alvin thank u

[edcmat-l1]

You aren't logging any torque pids. But even without them I'd bet raising the last 2 or 3 rows of your driver demand tables will cure the throttle closing.

It would also help to know what's done to the vehicle. Without all the pertinent info all anyone can do is guess.

[Jmarkum5]

You aren't logging any torque pids. But even without them I'd bet raising the last 2 or 3 rows of your driver demand tables will cure the throttle closing.

It would also help to know what's done to the vehicle. Without all the pertinent info all anyone can do is guess.

pidlog.hplpidlog.hplthis is file

[Jmarkum5]

i did up driver demand didnt help i changed pids in log to for yall

[Jmarkum5]

i did up driver demand didnt help i changed pids in log to for yall

just a bolt on e85 car lt2 intake nothing special

[Jmarkum5]

just a bolt on e85 car lt2 intake nothing special

No body dang left me hanging just needed help thanks guys

[Alvin]

Honestly you are not making it easy to help you. You are putting the bare minimum in these post. It's the equivalent of dropping a car off at a shop with a note that says JUST FIX IT.

It's likely going to be a torque limiter somewhere.

You could better explain what's going on. You can post your stock file so we can see what you've edited.

PS no need to send me emails or PM's telling me to check this thread. There's been 5 now.

[Jmarkum5]

Honestly you are not making it easy to help you. You are putting the bare minimum in these post. It's the equivalent of dropping a car off at a shop with a note that says JUST FIX IT.

It's likely going to be a torque limiter somewhere.

You could better explain what's going on. You can post your stock file so we can see what you've edited.

PS no need to send me emails or PM's telling me to check this thread. There's been 5 now.

i posted file and said whats wrong 18 ss close throttle on shifts in 5th gear bad

[Jmarkum5]

[QUOTE=Alvin;821326]Honestly you are not making it easy to help you. You are putting the bare minimum in these post. It's the equivalent of dropping a car off at a shop with a note that says JUST FIX IT.

It's likely going to be a torque limiter somewhere.

You could better explain what's going on. You can post your stock file so we can see what you've edited.

PS no need to send me emails or PM's telling me to check this thread. There's been 5 now.[/QUOTEpidlog.hpl021425_Trans_6400_Test_2jd.hpt18_021721_JM_Mod_3 (1).hpt last file is stock says mod

[Jmarkum5]

pidlog.hpl

021425_Trans_6400_Test_2jd.hpt021425_Trans_6400_Test_2jd.hpt

[Jmarkum5]

bolt on car camaro ss throttle closeing before shifts 5th gear bad pidlog.hpl021425_Trans_6400_Test_2jd.hpt

[Jmarkum5]

what else is there to no i said problem and posted log and file