Results 1 to 13 of 13

Thread: Flashing a reman computer.

  1. #1
    Tuner
    Join Date
    Aug 2004
    Location
    michigan
    Posts
    56

    Flashing a reman computer.

    Flashing a reman computer. Can you flash a reman computer with HP Tuners software? Or do you have to have it flashed and then make the changes to the program. This is on a 97 Corvette.

  2. #2
    Супер Модератор EC_Tune's Avatar
    Join Date
    Apr 2003
    Location
    Almost 2000 feet.
    Posts
    7,876
    If you have a 97 LS1 program you can do a Write Entire on it.
    Always Support Our Troops!

  3. #3
    Tuner
    Join Date
    Aug 2004
    Location
    michigan
    Posts
    56
    Thanks for letting me know. I was not sure I could do it.

  4. #4
    Advanced Tuner uarperformance's Avatar
    Join Date
    Apr 2007
    Location
    Largo
    Posts
    255
    Having 07 corvette pcm replaced. Do I need to repurchase license for new pcm?

  5. #5
    Tuner
    Join Date
    Aug 2004
    Location
    michigan
    Posts
    56
    I flashed the new PCM with wright entire PCM and did the vin and vats and the car will not turn over with the key. So I tried to put the old pcm and it does the same thing . Nothing. Is there something I am missing?

  6. #6
    Супер Модератор EC_Tune's Avatar
    Join Date
    Apr 2003
    Location
    Almost 2000 feet.
    Posts
    7,876
    Car won't start or the starter works but car dies?
    If the latter, try disabling VATS temporarily and see if it starts and runs.
    Always Support Our Troops!

  7. #7
    Tuner
    Join Date
    Aug 2004
    Location
    michigan
    Posts
    56
    Thanks!!! It started after I disable the VATS. Now how can I turn it back on without the same problem?

  8. #8
    Супер Модератор EC_Tune's Avatar
    Join Date
    Apr 2003
    Location
    Almost 2000 feet.
    Posts
    7,876
    The VATS relink procedure for Gen III engines takes 10 minutes - no less:
    1. Try to start vehicle - it may start and stall or not crank at all
    2. Very Important: *Leave key in on position*
    If you turn the key off you have to start all over again
    3. Click on Relink VATS on the Flash menu
    4. Wait 10 minutes
    *Security* light on dash will go off after 10 minutes
    5. Pull key from ignition
    6. Wait 10 seconds
    7. Start vehicle
    If the vehicle doesn't start, repeat the entire procedure as a step may have been skipped.
    Last edited by EC_Tune; 05-03-2008 at 02:07 AM.
    Always Support Our Troops!

  9. #9
    Tuner Doubledip's Avatar
    Join Date
    Apr 2007
    Location
    Sydney, Australia
    Posts
    161

    vats

    can you link a e38 to a either 2nd hand or new pim with HPT?

  10. #10
    Tuner bigbrian442's Avatar
    Join Date
    Sep 2007
    Location
    Pasadena, Maryland
    Posts
    174
    Quote Originally Posted by uarperformance
    Having 07 corvette pcm replaced. Do I need to repurchase license for new pcm?

    YES. Unless you have the model year license.
    Last edited by bigbrian442; 05-12-2008 at 03:18 PM.

  11. #11
    Quote Originally Posted by EC_Tune
    The VATS relink procedure for Gen III engines takes 10 minutes - no less:
    1. Try to start vehicle - it may start and stall or not crank at all
    2. Very Important: *Leave key in on position*
    If you turn the key off you have to start all over again
    3. Click on Relink VATS on the Flash menu
    4. Wait 10 minutes
    *Security* light on dash will go off after 10 minutes
    5. Pull key from ignition
    6. Wait 10 seconds
    7. Start vehicle
    If the vehicle doesn't start, repeat the entire procedure as a step may have been skipped.
    Actually, the process takes 30 minutes, as you have to go through the cycle 3 times (with a start on the 4th try).

    --Brian

  12. #12
    Супер Модератор EC_Tune's Avatar
    Join Date
    Apr 2003
    Location
    Almost 2000 feet.
    Posts
    7,876
    Quote Originally Posted by brianko
    Actually, the process takes 30 minutes, as you have to go through the cycle 3 times (with a start on the 4th try).

    --Brian
    Correct only if you don't use a Tech2 or you don't use the BCM Relink procedure above. It works correctly in 10 minutes with the HPT BCM Relink on all the vehicles I have used it on.
    Always Support Our Troops!

  13. #13
    Potential Tuner
    Join Date
    Aug 2019
    Location
    British Columbia
    Posts
    2
    Hey Guys, I am still pretty new to HP tuners and GM vehicles and PCMs. Will the Vats stop a P01 pcm Fuel pump relay 12v signal?