2003-2007 6.0L Powerstroke Diesel is now supported in 2.25 Beta

[Eric@HPTuners]

It's finally here.

2003-2004 (448K Oak ECM) and 2005-2007 (512k Oak ECM) are now supported in the latest beta. Every read that has been sent to us over the last several years has been added.

I will be working on adding TCM support over the next several weeks.

[Eric@HPTuners]

Updated thread. 2003-2005 6.0L Diesels are now supported.

[superwagon]

Awesome! I have had countless request for tuning these over the years. I hope they come looking again soon!

Thanks again Eric!

[22eco]

This is awesome.. so does this mean I should hold off on getting a tuner for my 6.4l powerstroke?

[Eric@HPTuners]

This is awesome.. so does this mean I should hold off on getting a tuner for my 6.4l powerstroke?

I can't give you an ETA, but it only took me a month to get the 6.0L done. I would expect to be able to get the 6.4L done in a couple months.

[richsoucie]

I can't give you an ETA, but it only took me a month to get the 6.0L done. I would expect to be able to get the 6.4L done in a couple months.

how long until the scanner is working so we can monitor the oil temp, coolant temp, trans temp and ficm voltage with 2.24 scanner i think all we get is coolant temp

[kruisecontrol]

this is great news! thank you , TCM support is equally important , I need tcm support for the 6.0 cummins conversions I do using the 5r110, this will be great.

[kangsta]

will the 2015 6.7 be on the radar?

[playtoy_18]

Just read my first diesel,got an error message afterwards "Validate Checksum Failed,you will be unable to save or flash this file".
It saved 182kb file though,and it opened up and showed some parameters.
Something odd about this duck though,Hp nor Ford IDS will recognize the VIN and I have to enter it.
It is updated to latest calibration available currently.
Any info?
This is a 2004 F350 6.0,I downloaded the latest Beta after the first read did the same thing.

[Eric@HPTuners]

Just read my first diesel,got an error message afterwards "Validate Checksum Failed,you will be unable to save or flash this file".
It saved 182kb file though,and it opened up and showed some parameters.
Something odd about this duck though,Hp nor Ford IDS will recognize the VIN and I have to enter it.
It is updated to latest calibration available currently.
Any info?
This is a 2004 F350 6.0,I downloaded the latest Beta after the first read did the same thing.

Send the file into support, and I will take a look.

[Tiffo60]

you wouldnt happen to have an 06 stock file i could look at?

[Eric@HPTuners]

you wouldnt happen to have an 06 stock file i could look at?

http://www.hptuners.com/forum/showth...l=1#post371613

[edcmat-l1]

you wouldnt happen to have an 06 stock file i could look at?

If you need another one, I have the one out of my personal pig. You can email me at the address in my sig.

[khislop007]

Hey guys, how do I get 2.25 beta? I have a '05 psd 6.0 that I would just like to use the VCM scanner to check my coolant, oil, tranny temps etc...

Any help would be great! Thanks

[Tiffo60]

Hey guys, how do I get 2.25 beta? I have a '05 psd 6.0 that I would just like to use the VCM scanner to check my coolant, oil, tranny temps etc...

Any help would be great! Thanks

email support with your info

[Eric@HPTuners]

Just wanted to add that I have about 7 or so of the latest 6.0L TCM OSIDs now supported. I should be done tomorrow having all of them supported. So we can now say that the 6.0L ECM and TCM is supported!

[richsoucie]

Ficm ?

[Eric@HPTuners]

Ficm ?

Possibly..

[63chevy]

Ficm ?

I second that!

[Tigre_loco]

Eric,

Do you still need more TCM reads? I've got 2 I can get you this weekend if you're still looking for some.