I would like to be able to turn my cooling fans on in the staging lanes and between runs, while keeping the engine off. I was going to wire up a switch to override things and be able to do this but a Diablo Trinity owner stated the Trinity allows this. Is this a feature that could be added to our special functions? The ones added recently were fantastic so I thought I would ask about a fan override as well.
2013 Dodge Challenger RT Plus - Shaker
I would like this also as my GM truck tune has this.
[ECM] 8061 - Ignition Off Fan Run Time: Run time for fans if Ignition Off Fan Disable Temp is exceeded at ignition off.
2013 Dodge Charger R/T Plus, Stock 5.7L, Edelbrock E-Force Stage 1, 3.25" Pulley, 450-HP 459-TQ.
Corsa Sport CatBack, 3.06:1 Wavetrac, Dual Fans, 1-7/16 Radiator, Mopar Oil Cooler
2005 Radix'd Silverado L33 5.3 ECSB Z71 @ 387-HP 395-TQ
I would also like to browse the section without having to be connected to a vehicle to give it a study.
2013 Dodge Charger R/T Plus, Stock 5.7L, Edelbrock E-Force Stage 1, 3.25" Pulley, 450-HP 459-TQ.
Corsa Sport CatBack, 3.06:1 Wavetrac, Dual Fans, 1-7/16 Radiator, Mopar Oil Cooler
2005 Radix'd Silverado L33 5.3 ECSB Z71 @ 387-HP 395-TQ
We will look into it. Thanks!Originally Posted by Pector55
Please email support with parameter requests. Although, it's quite possible your Dodge vehicle may not have this parameter as GM and Dodge are quite different.
Neon Srt4 scanner support.... please please please with a cherry on top.
Dear god yes. ^^^^^^^
on all the 15's I've tuned I'm getting codes that will not clear. Even with the "special" dodge reset. Noticing U0100 popping up too just reading the file out. Have to delete it out of the tune to get rid of the engine light.
2018 Camaro SS, Maggie 2650, 103 TB, Big Gulp, E85
Hello,
The window of controls and special fonctions is blank :-(
what's wrong ?
Grand Cherokee 2012 ECM NGC4A
Last edited by Jimmy; 09-17-2016 at 09:02 PM.
Email Support.
Make sure to include a VCM Suite Infolog while connected to the vehicle.
What do you mean by "infolog" ?
Thanks
Email support Is : [email protected] ?
Information on what an InfoLog is and how it can be obtained can be found here: http://www.hptuners.com/forum/showth...acting-support
You are correct.
Hello,
Any time frame on Trans tuning for 05 PCMS?
Thanks
Jared
tuning on 14' Viper replaced the Throttle bodies and need to do relearn. I click the special functions tab and it is blank. It works on the GM models just fine. Am I doing something wrong?
VCM Suite 3.2 brings all new special functions to Chrysler support. Located within "Controls and Special Functions" in VCM Scanner 3.2, you will notice even more controls & special functions than before
New functions include1:
- Throttle Relearn: Will perform a throttle relearn for vehicles equipped with ETC.
- Reset All Adaptives:Resets all adaptives (fuel trims, etc.)
- Clear DTC: Chrysler Specific DTC Clear. Recommended to use along with the standard "Clear DTC" in "Diagnostics and Info"
- Gear/Tire Adjustment: Was in 3.0 as well. Change your tire size and/or adjust gear ratios using this special function.
- Traction Control Disable: Will disable Traction Control. Depending on the vehicle, you may need to do this after every key cycle. (Off-road use only)
- Traction Control Enable: Re-enables traction control after you have disabled it, if it doesn't re-enable on it's own.
1(Available functions may vary depending on what your vehicle supports)(Currently only for 2007+)
Yes I saw that post but when I attempt to do that on the 14' viper i get non of those options its just blank.
Have you already written the base file, or are you trying to do the relearn on a non-modified Viper PCM?
Yes the car has been tuned with the cable I am using. Its a modified viper. Has had more than 1 hp tuners tuner write a file on it if that matters.
I know the feature has been available in the past, at least for Gen 4s. Have you emailed support?
Reply With Quote