Results 1 to 12 of 12

Thread: E85 Conversion - 2016 Scatpack

  1. #1
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8

    E85 Conversion - 2016 Scatpack

    I just want to sanity check my approach here if anyone is willing to lend some input.

    I'm switching over to a straight E85 tune since this isn't a factory WB car like the Hellcats (so the flex fuel patch is NOT applied in this case). The car is a 2016 Charger Scatpack, so it's an A8 392. It has an intake and exhaust (with factory cats) along with an AEM wideband.

    Here's my approach:

    - Adjust FA Stoich values for E85
    I'm assuming a pure E85 blend here and no winter blends to account for since it's not running the flex fuel patch with any kind of ethanol content inference. Stock value looked ever so slightly rich to me (maybe to split the difference with E10?).

    - Adjust PE Aircharge and PRatio tables
    I worked out a spreadsheet to compute the target FA and lambda values based on the new stoich values plus the PE adder values. I then compared to lambda for E85. They were a bit leaner after the stoich point change so I've added roughly 30-35% to the PE tables as a starting point, which puts commanded lambda somewhere between .80 and .87 after the E85 switch depending on the cell. I figure I can adjust if need be, but that should be a close starting point.

    - Adjust WOT Spark
    Plan to tune on the dyno. But generally, I expect about a max of 3-4 degrees additional based on what I've read about these cars.


    I have a couple of questions now:
    • Open Loop/Base - Do I need to add fuel to the cold/warmup table to account for more difficult starts on E? I've seen others mention the Startup Inj PW table for startup. Which would be correct, or is it both?
    • Fuel Mass Multiplier - I've noticed the alcohol multiplier table here for flex fuel as well. Should this change to account for E85?
    • Injector PW - I've heard people talk about changing this, but wouldn't the adjusted stoich values negate the need to adjust here? I'm aware of the approach many take with ANN on to adjust Inj PW instead of VE tuning. But isn't that to account for airflow characteristics rather than fuel characteristics?
    • Have I missed anything else?



    And pardon me if any of these are obvious. I'm fairly new to this. The little bit I did know was GM based and probably out of date by now.

  2. #2
    Senior Tuner
    Join Date
    May 2015
    Posts
    1,744
    Change your stoich, change your PE tables to get a proper lambda, leave EVERYTHING else the same until you get it on the dyno.

    Startups should be relatively the same as long as your startups on regular 93 were ok. In colder months (sub 45 degrees) you will need to add some fuel to the lower coolant temps in the startup inj pw table (go small, 5 % changes can do a lot).

    Once on the dyno add timing but don't go too crazy, e85 has a tendency to never show preignition on your knock sensors even when it is, and you can easily lose a ring land with that 392.

  3. #3
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8
    Quote Originally Posted by 06300CSRT8 View Post
    Change your stoich, change your PE tables to get a proper lambda, leave EVERYTHING else the same until you get it on the dyno.

    Startups should be relatively the same as long as your startups on regular 93 were ok. In colder months (sub 45 degrees) you will need to add some fuel to the lower coolant temps in the startup inj pw table (go small, 5 % changes can do a lot).

    Once on the dyno add timing but don't go too crazy, e85 has a tendency to never show preignition on your knock sensors even when it is, and you can easily lose a ring land with that 392.
    Good to know on the startups and other tables. Definitely didn't plan on adding any timing until on the dyno, so we're good there. Appreciate the input!

  4. #4
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8
    Update, first tests after switching over to E85 logged today. Fueling seems close, but in PE it's running tad bit lean. I left the Alcohol Fuel Mass Multiplier at 1. When I tested setting it at a value that you'd expect for 85% alcohol, it ran way lean in PE. Moving in the opposite direction, it goes richer. Maybe I'm missing something here, but why do the flex fuel vehicles have these multipliers set as low as 0.930 for 85%? Wouldn't you expect more fuel mass for E85? My actual lambda in PE seems close to dead on target with the alc fuel mass multiplier set somewhere around 1.03. And if not this multiplier, what else could cause it to go so much leaner in PE?

  5. #5
    Senior Tuner
    Join Date
    May 2015
    Posts
    1,744
    What fuel are you using, real pump e85? Did you test your concentration?

  6. #6
    Advanced Tuner
    Join Date
    Jul 2015
    Posts
    861
    I'm asking because I don't know. But if you change the stoich to E85, is the alc fuel mass multi doing anything? If it's not using "Flex fuel" will it even reference that table?

    Is the stock fuel pump/injectors big enough to support E85? Again I'm asking because I don't know.

    What is your injector duty cycle?

  7. #7
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8
    I'm on pump E85. I have it measured at 74% ethanol according to the Innovate ethanol gauge. I can adjust my stoich for that. Still doesn't explain why the fuel mass multiplier works in the opposite direction than I'd expect.

    Jay - The multiplier still works and is used. It's just a 1x1 table for 0% alcohol in a non ffv.

    I had trouble with my inj duty cycle logging. I think I have it figured out today, so I'll have to get some new logs. Stock pump and injectors should be fine for a mostly stock, NA 392. But it's definitely worth checking. I thought that too but brushed it aside because it should be fine.

  8. #8
    Senior Tuner
    Join Date
    May 2015
    Posts
    1,744
    can you post up your tune? I want to see your PE tables.

    Problem with the multiplier is it is used against other alcohol tables, which for the most part have zeros or are missing entirely unless you perform the FF patch, with the exception of your PE tables which are used no matter what alcohol % you have. So i think the multiplier is being used against a zero table somewhere. In the hellcats, tables are populated and so works as expected.

  9. #9
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8
    Quote Originally Posted by 06300CSRT8 View Post
    can you post up your tune? I want to see your PE tables.

    Problem with the multiplier is it is used against other alcohol tables, which for the most part have zeros or are missing entirely unless you perform the FF patch, with the exception of your PE tables which are used no matter what alcohol % you have. So i think the multiplier is being used against a zero table somewhere. In the hellcats, tables are populated and so works as expected.
    Here you go. This is the E85 version, not the one adjusted for 74%.

    I don't see where that multiplier would apply other than the base fuel mass values, but perhaps.
    Attached Files Attached Files

  10. #10
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8
    So I got my inj dc logging fixed tonight. I'm barely running out of injector up top. Looks like it'll need larger injectors after all.

  11. #11
    Potential Tuner
    Join Date
    Apr 2019
    Location
    Pittsburgh, PA
    Posts
    8
    In other news, I got my cold starts worked out nicely. ID 1050x injector set ordered today to solve the injector sizing.

  12. #12
    Advanced Tuner
    Join Date
    Jul 2015
    Posts
    861
    Quote Originally Posted by PittPaz View Post
    I'm on pump E85. I have it measured at 74% ethanol according to the Innovate ethanol gauge. I can adjust my stoich for that. Still doesn't explain why the fuel mass multiplier works in the opposite direction than I'd expect.

    Jay - The multiplier still works and is used. It's just a 1x1 table for 0% alcohol in a non ffv.

    I had trouble with my inj duty cycle logging. I think I have it figured out today, so I'll have to get some new logs. Stock pump and injectors should be fine for a mostly stock, NA 392. But it's definitely worth checking. I thought that too but brushed it aside because it should be fine.
    It may be how HPT has it mapped. It is Chrysler though so there's no telling. FA stoich comes to mind, haha