Was doing the first full read of the system and received the error TCM read error loc 64800, thus the read fails.
This is on a 2003 LB7 Duramax and Allison combo.
Jon
Was doing the first full read of the system and received the error TCM read error loc 64800, thus the read fails.
This is on a 2003 LB7 Duramax and Allison combo.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
I went ahead and tried the full read again, this time it had a loc of 65000.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
I had this happen to me recently with an 07 cobalt because of the separate pcm/tcm...what you'll need to do is send an info log of the vehicle to support@ hptuners dot com and they'll probably give you a new beta version to try....a screenshot wouldnt be bad either
Thanks
Bill
It doesn't have to be perfect, it just needs to be done in two weeks...
A wise man once said "google it"
best way to grab a log? Was just going to try and grab a screenshot.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
It doesn't have to be perfect, it just needs to be done in two weeks...
A wise man once said "google it"
NOw that is good stuff, probably could have found that had I done a 10 second search. ;-)
Thanks, heading out to the truck now.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
OK, have a log and screenshot sent into support.
Thanks for the help Bill.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
not a problem jon, hopefully they get you up and running soon
It doesn't have to be perfect, it just needs to be done in two weeks...
A wise man once said "google it"
Sounds like something is not keeping quiet during the read/write process.
Try pulling the radio fuse and see if it goes away.
I had removed the onstar, I will try the radio fuse and see if that changes things.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
removed the radio fuse and now won't communicate with with the TCM at all from the looks of it.
Sent email to support.
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
Chris, wondering if you had a chance to check out the info I sent over with regards to the drivers.
Jon
Last edited by JuniorCruzer; 10-16-2006 at 03:22 PM.
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
Hi Jon,
i didn't receive an email.
Please resend the email to support as I will be out of the office today and Ken will have to take a look at it.
Chris...
I count sheep in hex...
I have verified that all the drivers are the main drivers and not the XP drivers. I have tried two different laptops and same issue on both. Errors out at around 64800 when reading the TCM each time. High speed, low speed, have gone through the truck top to bottom and pulled and reseated every connector I can find and still same issue.
I can read my buddies grandprix no problem.
When attempting to scan, seems I can scan everything except no transmission stuff, not sure if that was by design or something weird with mine.
After it fails, I need to remove and reconnect the USB cable for it to read the VCM again.
Half the time it seems to error out when attempting to setup security to the TCM, the other half it errors out at 64800.
I have 4 cables in the diagnostics port underneath the dash.
Truck is stock except bed rug, bed cover, side steps, new tires and radar detector.
I believe I have checked every fuse and all are good. I have removed radio, radio amp, and info fuse and also left them in, same issue no matter what.
I have reloaded the USB drivers off the CD, making sure that they are the standard drivers and not the 64bit drivers, I have reloaded the software from scratch.
I have undone the batteries for an hour and reconnected and same issue.
I am at a total loss.
Please review my PM and email to all of you with my phone number, any help would be appreciated.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
Can you elaborate on that please with some specifics?Originally Posted by JuniorCruzer
We got this guy Not Sure, ...
The port that I plug the HPtuners cable into has 4 wires in it.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
What im pretty sure he means is when you look into the diag. port, it has 4 shiny, gold pins. Mine has the same.
Correct, that is what I was refering to.Originally Posted by gman4dx266
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
OK, with a third laptop we were had two failures and two reads. I left my laptop on and connected to the truck for several minutes before I attempted any read of the truck and was finally able to get a successfull read. For some reason it seems the computer needs to be connected to the truck for several minutes before we are able to get a successfull read of the truck. On two of the fails, one was on the initial communication with the TCM and the other was at the standard 64800 location previously experienced.
I sent the current file from the truck into you all, the only change was to the speed limiter for testing of the write.
Any insite you all could provide would be greatly appreciated.
Jon
2012 Ram 3500 6.7 Cummins with Banks CAI, intake tubes, intake horn, grid heater/EGR/DEF delete, 4" Straight pipe
2017 Jeep Wrangler Rubicon Unlimited, Stock - but looking to change that
JC, when you say the truck is "stock", you men the PCM has never been tuned, and you do not have any LB7 controller hooked in like the EDGE or any other tuning products right?
The reason I asked is that I did recieve the same error when I first read the TCM with the EDGE/ATTITUDE still plugged in on my 2004.5 LLY. Once I uplugged that its fine for full reads and full writes.
Another possibiliity might be an electric brake controller for a trailer. I was OK with my Prodigy controller plugged in during writes and reads but I suppose a controller could be on the comms bus at key on.
Rick