Activity Stream

Try these channels out and lets see what the TM is doing. If you would get it up to operating temperature about 180* or more, then idle for a few...

Hello, is it already possible to use the Corvette PDR in race render br Heinz

Hi I try to check it when i am at home. I have A45, maybe we can share something. Say if you can log over 475Nm of torque 4500+rpm! It seems to be...

Yeah, it is. Grabbed a set cheap, last time tho...they shipped from Cyprus LOL They work fine, the issue is hot start after while. Extended...

You commented on an ancient post, but you want that STFT open loop off while tuning with the wideband. Otherwise the pcm will be trimming fuel...

All stock, modded? What the details here? Got the tune and logs?

Yeah, holy camshaft size for a big SUV. I hope it's got a 3,600rpm stall converter, otherwise it's going to suck to drive around. But the surge is...

I appreciate your input. I would love any advice you might have. As far as the camshaft, I've got it in 3 other trucks and it seems to work well with...

I am going to have to play with it. What all is done in your tune because it looks similar to mine minus MAF data. I basically copied what you had...

I appreciate the sarcasm. I don't typically like "stage" cams but this particular cam I have in 2 older gen 3 trucks and one 08 Sierra Denali. Seems...

perhaps they are in the middle of a move themselves? i hope they report back soon :)

You might also want to change transmission shift airflow - p/n - to 1's. I see hpt's at it again - forcing updates on everyone. I'm still not...

vgt open loop is off your pedal map could be more aggressive. needs more timing torque ratio vs speed limit make that all 1 idle hi cam add set...

see if this helps with your hanging idle. I was not able to view your logs. For whatever reason, it kept telling me that i cant view the log unless i...

With stock everything, and I mean stock everything, including the tuning, you can adjust the timing up way higher than 11 degrees in the very upper...

I?ll repeat myself, even though I hate repeating myself?. and I will add an extra word in, if you want a safe and reliable extra 200 hp, start...

just looked up that cam and that's a pretty big bumpstick. I do not have any experience on tuning with that much cam so disregard my comments about...

Question was how much timing can i throw at the truck Its 11* at 2900 rpm in main injection timing Was at 1600 egt i got it down to 1300egt at wot...

Thanks for the info Sir! Much appreciated.

Can VATS not being disabled properly block spark or does it block fuel only or both? Looks like I have everything needed to run except spark. I have...

Yes, the DTCs. I think why this comes up so often is, with no cats, and no downstream sensors, and the cat test enabled, it tries to run the test...

thanks Ls Rob ill do that also i dont know how to get into the o2 readiness and delay tables il look though its my first time getting into all this...

Ok, that makes sense. It is good to know that this is a normal thing and not my car flipping out. When you say the downstream O2s are turned off...

Increased slope = more fuel. If you change slope from .010 to .011, you are adding 10% fuel. But remember there is something wrong with your...

I made a few changes to base running airflow, didn't seem to help much for the throttle hang on a rev (downshift rev). Still have a few issues, 1)...

Your file does have it... it's just been removed in Editor versions newer than 4.8.7.

Sorry to hijack but I got a question for you blind. Should my e38 from 2015 camaro z28 have that cat test table in it? Im not seeing it in there...

As a side note I never understood why GM knowing that modifications are a fact of life, they did not, as smokeshow and a few others might understand...