Page 53 of 196 FirstFirst ... 34349505152535455565763103153 ... LastLast
Threads 1041 to 1060 of 3914

Forum: GM V8 Tuning - Engine, Gas (Gen 5)

(2014+, Direct Injection)

  1. Sticky Thread Sticky: Read Me!!! Tuning How-To's & General information

    Started by Bill@HPTuners, 07-23-2013
    • Replies: 6
    • Views: 73,271
    2011Camaro8
    12-21-2023 Go to last post

  2. Exclamation Sticky Thread Sticky: 2017+ GM Tuning - Important Information

    Started by Mark@HPTuners, 04-28-2017
    • Replies: 0
    • Views: 60,609
    Mark@HPTuners
    04-28-2017 Go to last post

  1. Predicted Axle Torque Source - Unknown 00 0A

    Started by vance580, 07-23-2022
    • Replies: 0
    • Views: 575
    vance580
    07-23-2022 Go to last post

  2. 2016 Camaro Low Pressure fuel pump

    Started by JackBauer, 07-23-2022
    1 Attachment(s)
    • Replies: 0
    • Views: 513
    JackBauer
    07-23-2022 Go to last post

  3. Negative timing and low rpm after cam swap 2018 6.2 L6

    Started by JASON11WS6, 07-21-2022
    • Replies: 6
    • Views: 1,528
    SultanHassanMasTuning
    07-23-2022 Go to last post

  4. 2015 sierra l86 8l90e

    Started by aaron_waldrop23, 07-22-2022
    2 Attachment(s)
    • Replies: 1
    • Views: 718
    aaron_waldrop23
    07-22-2022 Go to last post

  5. LT2 intake on L83

    Started by Estep40511, 01-17-2022
    • Replies: 4
    • Views: 3,211
    [email protected]
    07-21-2022 Go to last post

  6. LT4 output shaft speed sensor

    Started by 32vape, 07-20-2022
    1 Attachment(s)
    • Replies: 1
    • Views: 756
    radrace19
    07-21-2022 Go to last post

  7. log file needed please.

    Started by gerry_foster, 07-21-2022
    • Replies: 0
    • Views: 406
    gerry_foster
    07-21-2022 Go to last post

  8. C7 A8 Dyno power output difference 4th vs 5th gear

    Started by turabo87, 07-18-2022
    • Replies: 5
    • Views: 1,396
    sevinn
    07-20-2022 Go to last post

  9. L96 C10 Swap Both banks lean

    Started by Simonj, 07-18-2022
    2 Attachment(s)
    • Replies: 7
    • Views: 1,263
    Alvin
    07-20-2022 Go to last post

  10. 2016 Cadillac Escalade 6.2 - BTR Stage 3 Truck Cam

    Started by MarkTucker, 07-18-2022
    2 Attachment(s)
    • Replies: 1
    • Views: 1,468
    GHuggins
    07-18-2022 Go to last post

  11. Boost segment swap

    Started by nicul15, 07-11-2022
    • Replies: 5
    • Views: 1,383
    nicul15
    07-18-2022 Go to last post

  12. Options for Eliminating Downstream O2 Sensors

    Started by JKLTGuy, 12-02-2019
    • Replies: 12
    • Views: 14,925
    IARLLC
    07-16-2022 Go to last post

  13. Cam Adjusting

    Started by jlbjr, 07-15-2022
    • Replies: 2
    • Views: 867
    jlbjr
    07-15-2022 Go to last post

  14. C7 z06 torque management

    Started by atomic vette, 07-09-2017
    2 Pages •
    1 2
    3 Attachment(s)
    • Replies: 38
    • Views: 26,386
    JAMILRRR
    07-15-2022 Go to last post

  15. AT4 - Reduced power mode / MAF failed

    Started by Michalo187, 07-14-2022
    3 Attachment(s)
    • Replies: 1
    • Views: 718
    Darkhorse220
    07-14-2022 Go to last post

  16. VVE questions on cam angle and RPM/PR hysteresis

    Started by liviner, 07-13-2022
    • Replies: 0
    • Views: 532
    liviner
    07-13-2022 Go to last post

  17. Exclamation Car running lean while idling/cruising

    Started by SShelly, 07-12-2022
    3 Attachment(s)
    • Replies: 3
    • Views: 925
    SShelly
    07-12-2022 Go to last post

  18. L83 K5 swap problems

    Started by devlmaycry81, 09-29-2021
    1 Attachment(s)
    • Replies: 11
    • Views: 3,142
    2stimpy
    07-09-2022 Go to last post

  19. Modded Corvette 2017 sloppy at launch

    Started by se_sun1997, 07-06-2022
    2 Attachment(s)
    • Replies: 3
    • Views: 1,234
    GHuggins
    07-09-2022 Go to last post

  20. obs swap with l86 and 8speed trans

    Started by Rtex15, 07-08-2022
    • Replies: 1
    • Views: 763
    vannatta20
    07-09-2022 Go to last post
Page 53 of 196 FirstFirst ... 34349505152535455565763103153 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.