Page 1 of 130 123451151101 ... LastLast
Threads 1 to 20 of 2588

Forum: VCM Scanner

General product use: Scanning, Data Analysis, Layout Configurations, ...

Sub-Forums Threads / Posts  Last Post

  1. VCM Scanner External Sensors

    Configuration and use of A/D inputs and outputs.
    Wideband/Lambda/MAP/MAF/Other sensors...

    Forum Actions:

    Forum Statistics:

    • Threads: 1,362
    • Posts: 10,766

    Last Post:

  1. Sticky Thread Sticky: Permanent DTCs and VCM Scanner

    Started by Mark@HPTuners, 11-22-2016
    2 Attachment(s)
    • Replies: 17
    • Views: 61,295
    HartRod
    11-22-2024 Go to last post

  2. Sticky Thread Sticky: VCM Scanner V3 How-To / Getting Started Threads

    Started by schpenxel, 02-12-2016
    • Replies: 2
    • Views: 106,450
    mowton
    03-27-2016 Go to last post

  3. Sticky Thread Sticky: Important instructions when asking for V3.0 Scanner assistance

    Started by mowton, 02-10-2016
    • Replies: 0
    • Views: 50,524
    mowton
    02-10-2016 Go to last post

  1. Problems adding WB

    Started by Pavetim, 16 Hours Ago
    • Replies: 4
    • Views: 80
    Pavetim
    11 Hours Ago Go to last post

  2. Is there a way to tell how many in a cell were hits?

    Started by Pavetim, 3 Days Ago
    • Replies: 1
    • Views: 113
    aaronc7
    3 Days Ago Go to last post

  3. Polling rate extremely slow, even with only 3 polled channels - E38 Controller

    Started by supervette64, 1 Week Ago
    2 Pages •
    1 2
    7 Attachment(s)
    • Replies: 27
    • Views: 588
    LilSick
    6 Days Ago Go to last post

  4. Read DTC

    Started by lynyrd, 6 Days Ago
    • Replies: 0
    • Views: 52
    lynyrd
    6 Days Ago Go to last post

  5. VCM scanner freezing

    Started by Viking Motorworks, 2 Weeks Ago
    2 Pages •
    1 2
    3 Attachment(s)
    • Replies: 23
    • Views: 588
    Viking Motorworks
    1 Week Ago Go to last post

  6. Special functions and fuel trim reset?

    Started by Pavetim, 1 Week Ago
    • Replies: 0
    • Views: 96
    Pavetim
    1 Week Ago Go to last post

  7. HOw to tell which paramater to select

    Started by Pavetim, 3 Weeks Ago
    • Replies: 2
    • Views: 399
    LilSick
    3 Weeks Ago Go to last post

  8. 2021 Global B GM vehicle (Yukon w 6.2) - many missing variables (knock, misfire etc)

    Started by PSS, 07-20-2024
    • Replies: 4
    • Views: 10,333
    TriPinTaZ
    3 Weeks Ago Go to last post

  9. Help with AEM 30-0334/30-0333 Wideband to ProLink+ - Lambda Reading Stuck at 0.60

    Started by andnosobabin, 4 Weeks Ago
    1 Attachment(s)
    • Replies: 6
    • Views: 343
    LilSick
    4 Weeks Ago Go to last post

  10. missing parameters in math and filters.

    Started by tonn0297, 4 Weeks Ago
    • Replies: 2
    • Views: 512
    tonn0297
    4 Weeks Ago Go to last post

  11. new MPI3 pro link AEM 30 help

    Started by 18f1505.0roush, 4 Weeks Ago
    1 Attachment(s)
    • Replies: 1
    • Views: 162
    18f1505.0roush
    4 Weeks Ago Go to last post

  12. New to HPT but not new to tuning

    Started by Cometkid, 12-07-2024
    • Replies: 3
    • Views: 618
    Cometkid
    4 Weeks Ago Go to last post

  13. No IMRC status PID for 05-10 Mustangs?

    Started by Black_Sunshine, 12-17-2024
    • Replies: 3
    • Views: 163
    Black_Sunshine
    12-17-2024 Go to last post

  14. VCM scanner Causes car to die

    Started by jase2020, 12-06-2024
    • Replies: 1
    • Views: 770
    Pulse_GTO
    12-09-2024 Go to last post

  15. Angry Communication Issues

    Started by n_kremer36, 12-08-2024
    4 Attachment(s)
    • Replies: 3
    • Views: 581
    Bill@HPTuners
    12-09-2024 Go to last post

  16. Help wiring wideband to 0411 PCM EGR

    Started by Richard2325, 06-08-2024
    2 Attachment(s)
    • Replies: 5
    • Views: 1,288
    That1talon
    12-02-2024 Go to last post

  17. BCM functions

    Started by Bill@HPTuners, 01-17-2006
    2 Pages •
    1 2
    • Replies: 34
    • Views: 24,050
    Clubby
    11-30-2024 Go to last post

  18. vcm scanner

    Started by steve smith, 11-28-2024
    2 Attachment(s)
    • Replies: 0
    • Views: 636
    steve smith
    11-28-2024 Go to last post

  19. Scanner being laggy

    Started by CptFalcon, 11-10-2024
    1 Attachment(s)
    • Replies: 3
    • Views: 1,138
    Alvin
    11-27-2024 Go to last post

  20. AEM 4110 will read but won't show tables

    Started by motrhedx81, 11-24-2024
    8 Attachment(s)
    • Replies: 1
    • Views: 456
    motrhedx81
    11-26-2024 Go to last post
Page 1 of 130 123451151101 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.