Page 1 of 41 1234511 ... LastLast
Threads 1 to 20 of 810

Forum: Dodge Tuning - Engine, Diesel

Cummins, ...

  1. Sticky Thread Sticky: READ ME!!! General Dodge Diesel Tuning information and How To's

    Started by Bill@HPTuners, 02-04-2016
    • Replies: 3
    • Views: 39,677
    slvrwrx
    11-22-2021 Go to last post

  1. 12mm CP3 Tuning....need some help with FCA

    Started by xDiesel03, 2 Days Ago
    6 Attachment(s)
    • Replies: 13
    • Views: 241
    Jim P 2.0
    4 Hours Ago Go to last post

  2. 07 5.9 48re to g56 swap ecu

    Started by BMullikin, 4 Weeks Ago
    • Replies: 5
    • Views: 1,067
    CombatMech
    4 Days Ago Go to last post

  3. RAM 2007 with 5.9L Engine -> Stock Tune

    Started by DodgeBoy_8HP, 1 Week Ago
    • Replies: 1
    • Views: 504
    MAIDENCR
    1 Week Ago Go to last post

  4. Dodge ram 2020 6.7 cummins p061b need help

    Started by rstoco, 08-19-2024
    • Replies: 1
    • Views: 1,362
    DodgeBoy_8HP
    1 Week Ago Go to last post

  5. 48RE shift point tuning 05

    Started by modblaster, 08-18-2024
    • Replies: 7
    • Views: 2,989
    Jim P 2.0
    2 Weeks Ago Go to last post

  6. need 2004.5 cummins stock tune with vin 3D7KU28C34G245826

    Started by andtra, 04-16-2024
    • Replies: 2
    • Views: 1,110
    MAIDENCR
    2 Weeks Ago Go to last post

  7. New Truck, New to the Forum, Off the wall tune

    Started by 14GrayJ, 4 Weeks Ago
    1 Attachment(s)
    • Replies: 1
    • Views: 631
    MAIDENCR
    2 Weeks Ago Go to last post

  8. Pilot shutting off and significan power increase

    Started by MAIDENCR, 3 Weeks Ago
    • Replies: 0
    • Views: 539
    MAIDENCR
    3 Weeks Ago Go to last post

  9. 2005 Cummins 60HP Tow Tune - Help with Fuel Economy w/ Raised Rail Pressure Targets

    Started by RGHTBrainDesign, 07-30-2024
    10 Attachment(s)
    • Replies: 15
    • Views: 8,565
    Jim P 2.0
    3 Weeks Ago Go to last post

  10. 2004.5 cummins auto base file

    Started by [email protected], 4 Weeks Ago
    • Replies: 0
    • Views: 648
    [email protected]
    4 Weeks Ago Go to last post

  11. 2004.5 FMVB During the 1-2 shift trucks shuts off while throttle is still applied.

    Started by TwistedShafts, 11-02-2023
    1 Attachment(s)
    • Replies: 4
    • Views: 1,675
    [email protected]
    4 Weeks Ago Go to last post

  12. Early 04 scanner only 5 channels. Cm848

    Started by Powered By Tism, 03-30-2024
    • Replies: 3
    • Views: 1,489
    trophies
    09-06-2024 Go to last post

  13. 2450B Checksum Failure after flash

    Started by slimmons2009, 09-25-2023
    • Replies: 11
    • Views: 5,671
    [email protected]
    08-23-2024 Go to last post

  14. Misfire timing help

    Started by Justin77, 08-17-2024
    3 Attachment(s)
    • Replies: 6
    • Views: 1,919
    Jim P 2.0
    08-22-2024 Go to last post

  15. 2010-2012 Cummins Do Not Use HP Tuners to Read ECM

    Started by Jim P 2.0, 06-06-2024
    • Replies: 4
    • Views: 3,491
    Jim P 2.0
    08-18-2024 Go to last post

  16. 2015 CM2350 situation

    Started by RDTRCTR, 08-11-2024
    • Replies: 1
    • Views: 2,395
    dieselpitstop
    08-12-2024 Go to last post

  17. 2021 Ram 1500 Diesel ecu bosch EDC17C69

    Started by drhg, 06-26-2024
    1 Attachment(s)
    • Replies: 8
    • Views: 6,721
    Jim P 2.0
    07-23-2024 Go to last post

  18. Red or Blue, Doesn?t Matter. What?s Important is This

    Started by Jim P 2.0, 07-16-2024
    • Replies: 1
    • Views: 2,614
    jfreemanak
    07-16-2024 Go to last post

  19. Injector pulse width

    Started by Boosteds550, 07-07-2024
    • Replies: 6
    • Views: 4,255
    Jim P 2.0
    07-12-2024 Go to last post

  20. 2007 Ram 3500 CM2100 Previously Modified File

    Started by eurowise, 06-03-2024
    • Replies: 1
    • Views: 3,115
    Jim P 2.0
    07-10-2024 Go to last post
Page 1 of 41 1234511 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.