Check this website out, it should explain it.
https://www.gribble.org/cycling/air_density.html
Type: Posts; User: luke111
Check this website out, it should explain it.
https://www.gribble.org/cycling/air_density.html
Ok post up the files I can have a look at them.
Did you find the injector part numbers and then find accurate injector data for them?
It will obviously run like crap with the wrong injector data....
Is this your car or is it a customers?
Where do you live? If you live in Brisbane it might make things easier.
Does this thing have bigger cams than stock? Most stock barras idle at around...
I have had a look at the files you have posted. There are so many things wrong Im not sure where to start! Whoever has been playing around with this ecu clearly had no idea what they were doing!
...
I'd say its Tip In Retard. I had a look at the log where it goes into pre-ignition spark source. I've never seen that before. Are your ignition timing tables std?
I've had a play around with the...
File is attached.
I managed to get a 10.7@129mph on the weekend out of it so I'm happy.
I'm not sure how much its holding me back off the line at 75deg instead of 82deg.
Any help you can give is...
You're better off logging throttle angle in degrees. It should be around 80-82 degs at WOT. You can double check with the ignition on/engine not running.
I've seen on my car throttle clipped to...
The short answer is NO.
You really want to setup a histogram graph with vcm scanner and log your long term fuel trims.
My first guess is that your injector slopes are not set correctly. You can do...
The short answer is no it doesn't work.
I have connected the boost sensor to pin C02 and when I log the PID with forscan (No vcm scanner doesn't work), the sensor is stuck on 0.0kpa.
The LPG or the...
There should be no difference between base model XT and XR6 ecu's as they run the same engine and kW rating.
I have attached files from a BA & BF Ecus I've owned.
If you have a specific strategy...
There are a few in the repository. Search under ford australia. You mustn't be looking in the right spot.
If you are referring to Inferred Movement = 2800rpm then I have tried changing that higher (6000rpm) and its still there.
I have set Torque Management; Torque Ratio Clips; Spark Limit; Trans Trunc...
On my BF turbo setup with BTR 4 speed, I am seeing ETC clipped to 75 deg in 1st gear on launch. I have a 3200 converter.
I don't seem to get it on the street but If I have drag radials on at...
im using a innovate LC2 with a LSU4.9. It has been flawless so far.
I've got a ASU-153 BF Dedicated Gas ECU (HACCFY9) that I want to reflash with a turbo strategy. (HACCKJ6)
I'm hoping that the LPG ecu has the output for the wastegate solenoid and the input for...
Heres a screenshot of what it looks like on cruise control on a flat road. The ecu is doing this opening/closing of the throttle all by itself. This was set on Prop Gain 0.1 (Standard settings)...
I made some progress over the past couple of days by adjusting the Proportional Gain - Electronic Throttle; Feedback control.
I setup some datalog traces for ETC Desired vs ETC Actual and noticed...
Thats handy to know. Thanks!
Hope someone can please help me out?
I've got an issue with my car that I've never been able to sort out - with cruise control surging especially going up or down hills. Flat road its not too bad.
...
OK I've had a look at your tune. I don't know where to start. Looks like its still mostly NA settings. It all looks really bad to be honest.
This is my advice (take it with a grain of salt but it...
I've never heard of the FG map sensor swap but that's handy to know!
I cut the connector and resoldered the wires when I went from BA NA to BA turbo.
I see you are running strategy HAAN9AW - and...
It should be there under Airflow, General.
Post up a copy of the file your working with. I've done a few NA to turbo ecu conversions BA & BF. I should be able to help you get it going. PM me if you...
Make sure you are also logging ambient air temp in lh column.
I can see that you are missing the unit for AAT.
Looking at the expression for that I can see an error.
You have (50008.24) instead...
Can you be more specific of whats happening? Is it the chart on the bottom right not showing the trace? or can you share a screenshot? I forgot to add that you need to be logging these channels in...
I have attached some files to help.