Search:

Type: Posts; User: 5FDP

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Vats disable only requires a write calibration...

    Vats disable only requires a write calibration only on those computers. That should be all that is required to turn it off. You can check for other DTC's related to the anti theft system and set them...
  2. If it made 450hp on that timing, think of what it...

    If it made 450hp on that timing, think of what it could have made on that same pulley with more timing and you still would have had the fuel there.

    To me it needs more injector if you want to...
  3. You don't need the PRO feature. It just makes...

    You don't need the PRO feature. It just makes widebands easier and hooking up other stuff easier.
  4. Replies
    10
    Views
    74

    Yes. I asked because his LY6 harness won't...

    Yes.

    I asked because his LY6 harness won't have the stuff for the AFM system, so if that it not disabled it won't run correctly.
  5. Not sure how you plan to make any power at 2 to 5...

    Not sure how you plan to make any power at 2 to 5 degree's of timing. You're about 12-15 degrees short of where it should be. Your EGT's must be sky high.
  6. Replies
    10
    Views
    74

    The L76 have AFM/DoD too where as the LY6 is just...

    The L76 have AFM/DoD too where as the LY6 is just VVT.

    Did you delete the AFM/DoD system?
  7. Click the systems tab, then the systems options...

    Click the systems tab, then the systems options tab.
  8. Replies
    1
    Views
    36

    If the channel is already there but nothing shows...

    If the channel is already there but nothing shows up, then remove the channel while connected to the vehicle. Re-poll for supported parameters under the edit tab and add the channel back in. Pick...
  9. Replies
    1
    Views
    48

    Using a different file will just cost you more...

    Using a different file will just cost you more money.

    Use the file you have on the computer now and change the ETC setting from 1 to zero under the systems options. The drive by cable throttle...
  10. Replies
    3
    Views
    69

    You can't really mess things up if you read what...

    You can't really mess things up if you read what you are changing.

    Some tables will clearly state that you should not change them because it could render the PCM useless. Some of the electronic...
  11. Set the brake torque mngt from 1 to zero under...

    Set the brake torque mngt from 1 to zero under the systems options.

    Then set the abuse mode to 7,000rpm and 0 mph in the engines torque mngt tab. You can also max out the max torque vs rpm to 640...
  12. For the hell of it change the fail to 0hz and set...

    For the hell of it change the fail to 0hz and set codes P0101 and P0102 to MIL on first error as well.

    Are the linear and offset settings correct for the 3 bar MAP you have??
  13. Replies
    4
    Views
    50

    Does it have a factory radio and alarm system too?

    Does it have a factory radio and alarm system too?
  14. What is your question though? A log file of it...

    What is your question though?

    A log file of it running helps see how it's doing. It's hard to tune stuff on an engine stand. If it runs and doesn't stall out, that's pretty good. Without a...
  15. Replies
    6
    Views
    62

    Get a wideband if you don't have one yet.

    Get a wideband if you don't have one yet.
  16. Replies
    1
    Views
    57

    I need a log file to see how it's running. Is...

    I need a log file to see how it's running.

    Is it all stock?

    What's your fuel pressure looking like??

    Probably unrelated but you are not suppose to change the platform type. This is a truck...
  17. Replies
    3
    Views
    72

    In the scanner you can log knock retard, spark...

    In the scanner you can log knock retard, spark timing and cylinder airmass.

    Then just create the graph/chart or whatever to match the layout in the editor. This way you can track it with ease.
  18. Replies
    1
    Views
    61

    Speed density is pretty simple to tune, I'd have...

    Speed density is pretty simple to tune, I'd have no problems doing that. You just have to wire in a IAT sensor into the intake.

    A speed density operating system is offered on just about all the...
  19. Replies
    4
    Views
    112

    Your vehicle does not use the primary VE when in...

    Your vehicle does not use the primary VE when in speed density. It only uses the secondary table. This is why all your changes to the primary table are doing nothing.

    1998-2000 computers have...
  20. You can't log more than 1 MAP sensor channel. You...

    You can't log more than 1 MAP sensor channel. You have the SAE map sensor channel for the 1 bar sensor and you also are logging the 3 bar sensor channel.

    The 1 bar MAP channel must be removed. The...
  21. I mean for wide open throttle area's I don't...

    I mean for wide open throttle area's I don't really add any shift pressure, it's already pretty high to me. It's the light throttle and medium throttle area's that I add 10-20% to make it better....
  22. Too short of exhaust could cause the sensor to...

    Too short of exhaust could cause the sensor to act funny, I'd try adding a few extensions to your exhaust to make sure that isn't a problem. I assume your test stand is running 58 psi too right? If...
  23. I've removed maybe 10% from that before and...

    I've removed maybe 10% from that before and that's it.

    I can make the transmission do what I want through other changes. Like shift timing, shift speed, shift pressure and on-coming pressure...
  24. Ask them if they have a wideband sensor of their...

    Ask them if they have a wideband sensor of their own or will they use the one you supply them. Hopefully you are the one with the wideband already.

    A good tuner doesn't need to make two different...
  25. Use the same year files. A 2000 uses a...

    Use the same year files.

    A 2000 uses a different operating system than a 2001 vehicle and there are many differences between the two so not everything would copy over right.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4