Sorry Fat Fingers
Type: Posts; User: Cobradoc
Sorry Fat Fingers
I have sent all info requested. It was sent yesterday around lunch. Been emailing with Chris. So far no solution.
Bill I have ticket #22866. Thanks I did relicense it today, I had to get it done.
Has anyone else lost a vehicle license after their MPVI2 performed a firmware up date? I have been tuning off and on a car on the dyno. Shut down for the holiday and when I came back and plugged in...
I am working on a rock buggy with a 07 Escalade 6.2 and 6L80. Cannot get the TUTD to work. It will go to 2nd gear limp mode a couple seconds after being put into gear. I scanned the PRNDL. Using a...
Tuned like a champ with LTFT off. Made 706/757 on 14lbs. Drives great.
Well spent some time with this today. If I turn LTFT off via the scanner and zero them all is well. Tuned within 3% across the board. I have not figured out how to turn off LTFT in the tune.
Using factory exhaust manifold setup. Moved O2 Sensor closer to engine, no change. Pulled 30% and left bank followed right bank stayed and ran like crap. Still plugging away.
You know, I haven't tried that because left bank is dead on at +3%. Worth a try I suppose,
Runs ok no miss, no exhaust leak. Pull the plugs and you can tell right bank is rich versus left bank. Car makes crazy power but I can't be sure tune is correct if right bank is correcting +30-40%....
I have a 69 Camaro with a LT4 8L in to be tuned from another shop. Started working on it and noticed a 30-40% trim increase on B2. Swapped sensors bank to bank and issue stayed on B2S1. So I did all...
Yes sir. Its 11.5 at wot.
Working ona 69 Camaro with a LT4 supercharged engine in a 69 Camaro. Dynos well makes really good power but on the road it surges at WOT. It does well up to 3/4 throttle but above that its like it...
Thanks, swapped it back to stock revs per mile and its happy. How do we adjust for tire size?
9684096841
I tuned this 16 Camaro tuned well makes good power, drives great. BUT when you lay on it in 1st or 2nd you get a "Reduced Performance" " Reduce Clutch Use" message and it drops power then...
Using a MPVI Pro interface. Editor 4.0.12. Will read VIN and Operating system but when you attempt to read I get a "Unsupported Interface" Message.
Is there a Histogram to aid in logging and correcting IPC TQ error?
How do you reference back to the MAF Table voltage to make adjustments? Is there a conversion from Hz to voltage?
Working on a 15 Mustang GT. Looking to log MAF Voltage but there is not a PID for it in Scanner 4.0.12.?
Searched the forums and don't see a lot of info on this. Looking at the Comp VVT Cams. Curious if you are adjusting the VVT tables for these cams? With the limiter installed I would think tables...
Here is a Log with Throttle Learn on and one with Throttle Learn off. Both under the same tune. Bypass is good. No codes.
I tuned this 11 Challenger and during tuning idle acted great. Always followed target. Customer brought it back after a week idling high. Checked all mechanicals and for vacuum leaks. Everything...
Is there any advantage to turning NN back on once the VE tables have been recalibrated? Just finished a 11 6.4 with a procharger. Tuned the VE Tables with NN off. Curious.....
I am assuming that you may tune the pcm without unlocking the tcm?
This is the issue with email tech support. Too easy to fall through the cracks. Often very hard to explain a issue in text. Good Luck.....