Search:

If you disable DOD and do not disable the codes it will act like its missing at an idle.

only the last table in that list is used..

There is a pid you can logged "MAF status" or something alone those lines. Make sure it says MAF failed. Make changes to the last table in that list...

Some trucks come with quite a bit of fuel supply.. some don't.

Since this is a swap.> Have you checked fuel pressure while it feels like it's falling on it's face?

awesome!

Also the map sensors settings you are using do not match anything I have references too.. Which PN sensor are you using.

https://www.pcmofnc.com/2020/03/12/gm-map-sensors-1-bar-2-bar-3-bar/
...

This is the second time this week I've caught this for someone..

In GEN 3's there is two min PW settings that MUST BE changed when doing large injectors. Some people preach to modify this.....

It's going full throttle now.


Look into the GMPP catalog for the crate engine + 6l80 setups. The "stand alone" controller isn't one like you would think. It's not a separate box or anything.....

I'm not certain but this looks like the newish GMPP LS3 kit with a 6l80.. It comes with stand alone software for the T43 but it will read and somewhat work with HPtuners. In those setup/files the...

I doubt you could brick it..

Let it sit unplugged overnight.

On that model car. You do not need to make any changes. It might make some more boost and need fueling/spark changes.. but nothing like the old days with big throttle bodies and ETC scalars.

This looks like BTM to me.

You should have been instructed to hook up a brake wire when doing the GMPP kit. Double check instructions wiring.. in the meantime this might give you a work...

no they don't.. e40 tbss use 24x 1x cam.. E67 use 58x 4x

I happen to be on the dyno right now with a FPCM equipped car 2010 camaro.

I had to use a different scalar/offset than you did. What I did was measure voltage at a about 27psi and another at 58...

send a email to [email protected].. Explain the situation and what you'd like to do. They are smarter on the GM stock reprogramming (called SPS) than I am on what is compatible with what.

I...

That is correct.. You need GM reprogramming software to do that.. We have this. There are ebay sellers that can do this too.

yes..

Also people should realize there is a fairly wide window of fueling that makes the exact same power.. A NA setup will make almost identical (less than 5 rwhp if that) between 12.5-13.0
...

I understand. Sounds like the FPCM will always estimate lower FP than actual as it is only "subtracting a calculated fuel line pressure loss"

There is no chance you are accidentally having your...

I replied you should ASK Mike Noonan.. then gave a positive plug for his book as it was helpful to me. It cost NOTHING to ask Mike about this..

Good luck.

I add boost to engines with 11:1 all the time.. Like LS7.

You'll be fine.


Pick a good injector for this build.. one that comes with injector data. You'll want a 2 bar map sensor and...

3-5% are very tight already.

It will never be 0%.

This is a very dynamic thing.. The humidity can change.. we have no compensation for that.. the temp of the fuel and therefore the...

This what they were saying with TFS heads back when they came out.... We found you can shim the pedestal and get a nice wipe pattern on the tip. A roller tip is just a easy fix for bad geometry

I just double checked.. and it absolutely does have that ramp

see image.. you can see your file name in it.

146424

The VSS showing 158 isn't ideal. It's because the TCM isn't there.

The wiring for most ECM's are pretty much exactly the same. It wouldn't be a huge deal to reflash that computer as a 2010...

IAC is out 0.. meaning it cannot lower the idle anymore.

The IAC is either bad, or there is a airflow leak... vacuum leak, throttle body blade position, etc.

Easiest way to check IAC is use...