https://www.google.com/search?tbs=li:1&filter=0&q=site:forum.hptuners.com+12593058
Type: Posts; User: blindsquirrel
https://www.google.com/search?tbs=li:1&filter=0&q=site:forum.hptuners.com+12593058
147268
Might want to see to those codes that didn't get disabled...
147259
Has anybody tried doing the relearn with tools other than HP Tuners?
Fuel cut-off is 4000 in P/N, so it's not going to...
You have to post the tune file. It is not optional.
No, the injector data stuff is my One Weird Trick (see username). Most of the rest I'm clueless about.
The flow rate table is the least important, any errors there as long as they're linear, can be compensated real real easy with the VE/MAF tables. The Offset is a diff'rent beast.
There is a link...
So why is the MAF table so inflated over the stock one? Engine & other parts from the same donor as shown in the tune file, 2003 Silverado 1500 LQ4 4WD?
The MAF table is all about the...
https://newsroom.porsche.com/en_US/2023/motorsport/porsche-hypercar-gtp-prototype-963-technology-31050.html
That VE table is suspect, too. The stock VE that goes from 15-105 has the same number of cells as the new one that goes 30-210. If you correctly transfer a stock VE over to the new one, you get only...
Correct, the 0 kPa VAC column from your datasheet all the way across, which is because the rail pressure is always 58 PSI higher than whatever is in the manifold, thanks to the little reference hose...
Injector data wrong - flow rate is for a referenced regulator, offset vs volts vs vac is for returnless/non-referenced.
^^^ I'm just gonna copy/paste that sentence up above and save it in a text...
Ignore list
https://www.acdelcotds.com/subscriptions
The Camshaft Position (CMP) sensor is mounted through the top of the engine block at the rear of the valley cover. The CMP sensor works in conjunction with a 1X reluctor wheel on the camshaft. The...
Gen 3 engines have a 24x crank reluctor wheel, Gen 4 ECM can only use a 58x reluctor.
147103 147104 147105 147106
147107
And, you have a 228/232 110* cam, and haven't changed idle speed or BRAF even one little lick, and that's probably why it's trying to idle at -10* spark timing, which makes idle vacuum go to shit,...
OK, so how did you do a segment swap between your 2002 P01 with OS 12216125, and a 2005 P59 with OS 12592618?
Compare > Segment Swapper is greyed out and unavailable with these two files, because...
Are you still using all of everything from the donor vehicle, like BCM, ABS, cats/downstream O2s, etc? Or has nobody gotten around to setting up this file yet to be ready for a 'first start' in a...
Did you ever post the file you took the 80E segments from? Do you have the trans wired up to match the diagrams for whatever vehicle those segments came from?
If you find any of those numbers on both TCMs, or 24275873, they can take the same calibrations. Sometimes the numbers get updated/replaced between the build date and when parts get into the...
I'm being a pain about this because if the MAP sensor is reporting real numbers the next step is tearing it down to check the cam timing/install.
And at 5 inHg it read about 83 kPa, and 10" = 66, 20" = 32?
What does that have to do with programming a new TCM, which is the topic of the thread you jumped onto the end of here?
No, I mean the 2014 & 2015 should have the same Service Number TEHCM, so each could be reprogrammed with the other's calibration without bricking.