Search:

Type: Posts; User: 5FDP

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    80

    Go into the gear/tire wizard under the edit tab,...

    Go into the gear/tire wizard under the edit tab, change it to what you have and have it auto scale the transmission for you. See how it drives after that.
  2. Replies
    7
    Views
    66

    Factory fuel pressure is more around 58psi on...

    Factory fuel pressure is more around 58psi on these, so you will need to adjust the flow rate data for that.

    The spreadsheet looks like it already has the g/sec at 58psi, so that is just a copy...
  3. Replies
    7
    Views
    66

    Why wouldn't it work with the correct data? ...

    Why wouldn't it work with the correct data?

    Can you post that data here?

    Are they 80's at 43.5 or 58psi and what pressure do you have your regulator set at?
  4. Replies
    7
    Views
    66

    Cut the over/underspeed spark correction tables...

    Cut the over/underspeed spark correction tables down to +/- 8 degrees, right now it can swing the timing way too much. Play around with idle timing as well, it might want 18 degrees instead of 22.
    ...
  5. Replies
    7
    Views
    80

    Without a data log the engine tune looks mainly...

    Without a data log the engine tune looks mainly stock. A few changes to timing and PE settings, both of which look okay so long as you have no intake leaks, exhaust leaks and have proper fuel...
  6. Replies
    3
    Views
    55

    Getting more power that you can really notice is...

    Getting more power that you can really notice is not something to expect, so just know that. You might be able pick up 10-15hp on 93 octane but I can bet you that most people aren't going to pay...
  7. Replies
    9
    Views
    93

    Time to hook up a fuel pressure gauge then. ...

    Time to hook up a fuel pressure gauge then.

    Also add your injector pulse width avg for both banks and your o2 sensors. Make it easier to compare that data on the logs.
  8. Replies
    9
    Views
    93

    Do you have a wideband o2 sensor installed on...

    Do you have a wideband o2 sensor installed on your car??
  9. Replies
    9
    Views
    93

    Why do you say it's dead lean? I don't see the...

    Why do you say it's dead lean?

    I don't see the o2 sensors or wideband data in the logs to verify that.

    And don't just blast the MAF/VE with fuel to make it not lean or rape the PE table to...
  10. Replies
    3
    Views
    91

    A tech 2 or MDI can program the computer. This...

    A tech 2 or MDI can program the computer.

    This is just my idea of making it work. The 4.3 to V8 swaps seem easy until you want the computer stuff to work seamlessly with the current truck.
  11. Replies
    8
    Views
    131

    You have to pay to license it again. New computer...

    You have to pay to license it again. New computer means new license.
  12. Replies
    14
    Views
    251

    Changing OS's on older computers like the P01/P59...

    Changing OS's on older computers like the P01/P59 may be what you read about, those are different than the GEN 4/5 computers.
  13. Replies
    3
    Views
    91

    I think if you could flash the computer with a...

    I think if you could flash the computer with a 6.0/5 speed file from a 2004 truck you may be in the best situation.

    Your computer already has the IAC drivers on it because the 4.3's still ran a...
  14. Replies
    1
    Views
    40

    The remote tuning network thing is on your tuner....

    The remote tuning network thing is on your tuner. He needs to send you a file that is not tuner locked.
  15. Maybe. I turn VATS off on everything that old, so...

    Maybe. I turn VATS off on everything that old, so I don't have that problem.

    Last thing I want if for someone to tell me that they tried to turn their car/truck on in the parking lot and the...
  16. The 2 bar OS changes the linear and offset...

    The 2 bar OS changes the linear and offset settings to 200/10.33 and if the stock MAP requires 94/10.33 it won't run right.

    I always disabled VATS on upgraded OS's to prevent weird issues with it....
  17. The 2 bar one has the MAP pegged at 105kpa,...

    The 2 bar one has the MAP pegged at 105kpa, possible you didn't switch back to the 1 bar MAP settings there.

    Is VATS still enabled at all??
  18. Why didn't they keep it if it helps so much? ...

    Why didn't they keep it if it helps so much?

    The calibrations changed when the EGR was removed and you could get the same fuel mileage or better without the EGR.


    The diesel thing is a can of...
  19. Replies
    13
    Views
    195

    I guess support will be the only way. My...

    I guess support will be the only way.

    My application key comes right up when I do it on mine.
  20. Replies
    13
    Views
    195

    Open the editor and put your MPVI into the...

    Open the editor and put your MPVI into the computer, then click the blue information dot. Click the information dot again and it will bring up all your data on the MPVI. All the cars you have a...
  21. Email support, there is no phone number. Even...

    Email support, there is no phone number.

    Even try the 2 bar OS with 1 bar MAP settings, see if that works for you.
  22. Replies
    13
    Views
    195

    Create a new account, we all had to do it. ...

    Create a new account, we all had to do it.

    Then add your MPVI into the devices section and everything should sync back up.
  23. I'd probably go with the larger injectors.

    I'd probably go with the larger injectors.
  24. You can screw something up pretty good if you...

    You can screw something up pretty good if you have zero clue what you are doing. Likely why it's not a good idea to make a change you don't fully understand.

    Reading forums, taking a course and...
  25. Replies
    1
    Views
    58

    You applied the speed density upgrade but never...

    You applied the speed density upgrade but never built out your 3 new VE tables.

    With zero data in them, it won't run.

    You will also find that the VVE tables that you need to copy from has the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4