found a way to make it easier, filtering by APP does the job :)
Type: Posts; User: wasyl
found a way to make it easier, filtering by APP does the job :)
i went thru couple of threads but my English is to poor to fully understand it and cannot figure it out by my self.
I'm trying to tune MAF open loop with WB using AFR Error math parameter. 2011...
will do tomorrow, thanks in advance for the help
update, i found that if i set engine>idle>airflow>min fail to 80 it idles fine when hot
ok i generated VE table and it fires and idles but lower then then set in table, thanks a milion
do you konw what base VE map i can use to make it run ?
no, still on stock MAP sensor, MAP is set to 128,38/-0,31 , MAP code is not showing anymore, it shows 100KPA in scanner with KOnEOff
Truck is 2011 GMC Yukon 6.2 6 speed.
Mods done:
E38 PCM form 2013 Yukon XL - 2 SD OS, VATS patches set to disable, starter patch set to disable, diagnostics for starter relay set do disable,...
Thanks for the input, I'll give this VVE one more chance
Best regards
I want regular VE.
I tuned lots of cars with different PCMs, standalones, carburetors both n/a and boosted and I must be dumb not to understand how to tune VVE PCMs. Did read all the threads, set...
Wish it was that simple, there was series if E38 PCM that did not have this feature and HPT team confirmed that. This is why I wonder if flashing firmware thru SPS with different VIN that has this...
my 2011 GMC Yukon is on E38 PCM without true VE table option, which cars/truck used E38 PCM with 2 bar OS that i can swap?
or is there and option to flash my PCM with SPS/Techline using different...
Yes, actually it is Yukon RWD, i did already switched in Trans->General->ECM Trans Type: Manual. All other things you mentioned are already working right, no christmas tree etc., even shifter lever...
I have swapped 8HP70 Jaguar transmission to 2011 Yukon truck. I had to switch trans type to manual so that car would turn on starter relay. Now my issue is that cruise control dos not engage because...
SPS2 (techline) does not allow to choose which trans should be set in PCM, and there is no access to old SPS system
I had to replace PCM on 2007 Pontiac Solstice, it is 2.4L I6 Automatic trans car. PCM (taken form 2009 Trailblazer/SAAB V8 truck) was reflashed with SPS2 using correct VIN number. SPS2 flashed it as...
is there any way to add VATS patch on first years of CTS/SRX V6 3.6 cars. i need to diable VATS/Passkey and under OS tab there is nothing that i can find on later years
or is there any other...
Hi there,
i do have here 2007 Dodge Charger 5,7 HEMI COP car. I'm having issues with fueling and after scanning i found that MAT calculations are proppably wrong and causing impropper fueling. MAT...
you can only see alcohol % in fuel in Scanner. Also there are two kinds of Flex sensors, one is physical and "second one" is only math parameter. Both give same result of alcohol % in fuel. I always...
today it started to work propperly
best regards
When trying roder licences i got message that Captcha is incorrect but there is no field. Tried oin two different PC's. Same on Contact page, it asks o input but there is no field for it and to...
I did 5.3 swap using ls1 injectors on E38 POCM. Does anyone know to modify E38 injector tables in PCM when ls1 installed ?
In "how to thread" is a dead link to universal injector spreadsheet :(
...
leave MAF calibration stock and just play with VVE, had same issue when swaping stock 5.3 to other car. For unknow reason PCM is not able to work propperly in SD/MAF mode, but in only MAF or only SD...
I'm goin' to carb 5.3 engine and need to control spark somehow. I do have spare PCM (HPT unlocked already) and engine harneess and was wondering if it is possible to run it in SD mode for spark...
good to know
best regards