Search:

Type: Posts; User: Ghostnotes

Page 1 of 15 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    576

    I'm dealing with WOT misfires as well, have for...

    I'm dealing with WOT misfires as well, have for months. Last year when i installed my supercharger, I guess somehow i nailed everything on the first shot. Being just an amateur, I figured there is NO...
  2. Replies
    48
    Views
    2,442

    Ok so I have finally had some decent time home to...

    Ok so I have finally had some decent time home to try to figure a few things out.First is how to set it to a 100% true open loop with absolutely noting in the way. I travel a lot and between honey do...
  3. Replies
    48
    Views
    2,442

    Finally got my zone boundary errors cleared up so...

    Finally got my zone boundary errors cleared up so hopefully i can figure out this misfire and move on.
  4. Replies
    48
    Views
    2,442

    Thanks everybody that cleared up a lot for me....

    Thanks everybody that cleared up a lot for me. Before my crash i must have been damn lucky with my tune because before i started trying to get into the VE it ran great. I had no surges and could let...
  5. Thread: Viewer?

    by Ghostnotes
    Replies
    0
    Views
    102

    Viewer?

    Has there been any thought about a viewer for the scanner? As in somthing for android. For instance if someone uploads a scan and you not around your laptop?
  6. Replies
    48
    Views
    2,442

    This is a log of the idle with engine warm. The...

    This is a log of the idle with engine warm. The first minute is with the forced open loop enabled with fuel trims cleared. About halfway through i re-enabled closed loop and re-cleared my trims.Am i...
  7. Replies
    48
    Views
    2,442

    Going to try again tomorrow to run a scan on it...

    Going to try again tomorrow to run a scan on it and will post it up.
  8. Replies
    48
    Views
    2,442

    No it's a YSi-V7, running 6 psi, as slow as i can...

    No it's a YSi-V7, running 6 psi, as slow as i can spin it right now. Stock diameter lower with a 3.8 upper. Technically it's not even awake yet. The block is built for max power, but I still have...
  9. Replies
    48
    Views
    2,442

    So just to be clear, 12.4 on an LT1 forced...

    So just to be clear, 12.4 on an LT1 forced induction is safe??

    I thought i mentioned that but did not looking back.
  10. Replies
    48
    Views
    2,442

    Ok I'll give that a shot. I do remember reading...

    Ok I'll give that a shot. I do remember reading somewhere here that 11.2-11.7 was used. TS books also called for the same. I always ran.85 on my NA cars port injection though.
  11. Replies
    48
    Views
    2,442

    Ok I'll give that a shot. I do remember reading...

    Ok I'll give that a shot. I do remember reading somewhere here that 11.2-11.7 was used. TS books also called for the same. I always ran.85 on my NA cars port injection though.
  12. Replies
    48
    Views
    2,442

    No its an Z51 LT1 but that's pretty much a moot...

    No its an Z51 LT1 but that's pretty much a moot point.
  13. Replies
    48
    Views
    2,442

    Is .75 lambda too rich for PE? Im running...

    Is .75 lambda too rich for PE? Im running straight 93 no meth.
  14. Replies
    48
    Views
    2,442

    Whoops i missed a one in there....its 1.197. ...

    Whoops i missed a one in there....its 1.197.

    The only thing i have not checked is injector voltage to see if there might be something going on there.

    It did not do it in the beginning. The car...
  15. Replies
    48
    Views
    2,442

    Ill check for exact when i get home. I think its...

    Ill check for exact when i get home. I think its 1.97xx but dont quote me. My WB sits at .75 lambda for shure.

    For PE that is...
  16. Replies
    48
    Views
    2,442

    Everything else is pretty good.It idles good, no...

    Everything else is pretty good.It idles good, no surging on part throttle and can idle at 6mph with no surging.
    If all this info going on in another thread with the VE,zone boundary errors and...
  17. Replies
    48
    Views
    2,442

    Thanks, I had some local person say just the...

    Thanks,

    I had some local person say just the opposite saying it was adding because i was not producing enough.
  18. Replies
    55
    Views
    13,887

    This is part of the issues i brought up well over...

    This is part of the issues i brought up well over a year ago. However at the time my calculation seemed to be inverse and overshoot. Not to mention getting zone boundary errors
    A good explanation...
  19. Replies
    48
    Views
    2,442

    It's at about 10* ish right now. I was...

    It's at about 10* ish right now.

    I was scanning a friends last week.....bone stick with around 15 to 18 warm...
  20. Replies
    48
    Views
    2,442

    I tried that and they would hang for too long and...

    I tried that and they would hang for too long and my WB swung wider. Now my WB is .98-1.02 again. Before it would swing from .95-1.08.
  21. Replies
    48
    Views
    2,442

    Thats it.

    Thats it.
  22. Replies
    17
    Views
    1,172

    Ok that's what i thought. Made me think for a...

    Ok that's what i thought. Made me think for a second that HPT created a master switch lately.....
  23. Replies
    48
    Views
    2,442

    Ok it was you not Higgs. That worked and I did...

    Ok it was you not Higgs.

    That worked and I did shorten the declared time and they are a perfect sinewave now with +/- 2%. Lambda is a lot more steady and only swings from .98/1.02 realtime...not...
  24. Replies
    48
    Views
    2,442

    Yes I am

    Yes I am
  25. Replies
    48
    Views
    2,442

    Here's what I'm talking about... I'm showing...

    Here's what I'm talking about...

    I'm showing some torque advance still, so I need to figure out which way to go with my torque settings. That I hope will settle my timing advance some more.

    Or...
Results 1 to 25 of 359
Page 1 of 15 1 2 3 4