Search:

Type: Posts; User: jball217

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Is there a stock file someone can post so we can...

    Is there a stock file someone can post so we can check it out?
  2. Replies
    8
    Views
    275

    I?ve had pretty good luck with rail pressure at...

    I?ve had pretty good luck with rail pressure at cruise being around 16-17kpsi
  3. Replies
    8
    Views
    275

    Getting your cruise timing up around 5-6* can...

    Getting your cruise timing up around 5-6* can really help with mpg and efficiency. And I?m sure that tune runs clean right now, there isn?t much fuel in it. But when you start getting more pulsewidth...
  4. Replies
    13
    Views
    319

    Weird how you cant see or download most tunes, I...

    Weird how you cant see or download most tunes, I just checked a few older threads from when I first got into this and I can still load them. As far as your timing goes, some areas the calculator will...
  5. Replies
    13
    Views
    319

    Im at sea level and ive always just copied and...

    Im at sea level and ive always just copied and pasted to every map. Air density gov, high speed gov low limit, smoke limit table, full throttle fueling tables, max output limit, torque limit, Main...
  6. Replies
    13
    Views
    319

    You wont hurt anything with that tune, but its...

    You wont hurt anything with that tune, but its not going to run like you want. There are a ton of limiters/governors left untouched that wont let the ecm command full fuel. Timing map needs to be...
  7. Replies
    8
    Views
    275

    Looks plenty safe to me. For the timing map did...

    Looks plenty safe to me. For the timing map did you copy and paste the whole table from a timing calculator? Also your rail pressure map looks pretty rough. Dont be afraid to throw more pulsewidth at...
  8. Replies
    6
    Views
    552

    94883 Data log from today, rail pressure isnt...

    94883 Data log from today, rail pressure isnt keeping up the best.
  9. Replies
    6
    Views
    552

    Dyno day was cut short, on my second pull the...

    Dyno day was cut short, on my second pull the truck spit out the rear freeze plug. Made 669hp and 1075ftlbs with 2800uS and 38* timing on the big end. I expected more torque from this setup, my 464...
  10. Replies
    6
    Views
    552

    I guess the main question is, will I be able to...

    I guess the main question is, will I be able to hurt the engine with my current tune on those chargers, or will I run out of fuel before I reach the limit of the bottom end?
  11. Replies
    6
    Views
    552

    Stock Internals and Compounds

    I just got a great deal on a used compound setup with a gated s364.5 and a s483, and I?m curious if I?ll now be pushing the limits of the stock rods? Long block is stock other than valve springs and...
  12. Replies
    2
    Views
    377

    I agree with ?what?s so hard about pushing the...

    I agree with ?what?s so hard about pushing the button? but our company has crane operators and millwrights and foremen who can?t figure out how to push that damn button. We have had 4 trucks in the...
  13. Replies
    2
    Views
    377

    4.3 6l80e tow haul

    I work for a company that has a fleet of Chevy pickups with the 4.3 6l80e, I would like to change the trans tuning so when you hop in and fire it up the trans will automatically go into tow haul...
  14. I have somewhat of a related issue, I have a tune...

    I have somewhat of a related issue, I have a tune JimP helped me a ton with and only on cold starts below 40F I get a nasty lope only at idle until ECT reaches around 55F. Kinda sounds like what...
  15. Replies
    1
    Views
    492

    Transient Rail Pressure table looks stock...

    Transient Rail Pressure table looks stock compared to the density based tables, high speed gov low limit should be raised, and if you're only going to be using the truck for sled pulling then timing...
  16. Thread: tune review

    by jball217
    Replies
    7
    Views
    759

    Looks like in your tune the cells are at a 5000...

    Looks like in your tune the cells are at a 5000 value.
  17. Thread: tune review

    by jball217
    Replies
    7
    Views
    759

    Air flow>General>Limits> Max Airflow, I changed...

    Air flow>General>Limits> Max Airflow, I changed all the 4500 cells to 6000, then I put min duty cycle to %60. Seems like I would "peg" the MAP at 51.4 Psi.
  18. Replies
    1
    Views
    430

    Here is the tune and the data log. I know rail...

    Here is the tune and the data log. I know rail pressure is low compared to desired, hopefully a lift pump will help that out.
  19. Replies
    1
    Views
    430

    2004.5 LLY Dyno Results

    Curious what you guys are getting out of a 100% stock LLY? I was able to get 400hp and 772ftlbs before rail pressure really started to drop off. This is the first Dmax I've tuned (my friends), though...
  20. Thread: tune review

    by jball217
    Replies
    7
    Views
    759

    Don't be afraid to throw more fuel at it. Also...

    Don't be afraid to throw more fuel at it. Also change your wastegate Min Duty Cycle Limit for more boost. When my truck was stock I was daily driving it with 3000uS of duration, and it was making...
  21. Replies
    20
    Views
    957

    Yeah I definitely should have listened, but...

    Yeah I definitely should have listened, but hindsight is 20/20. Ill try to get this tuned good, but if all else fails ill try to sell a low mile s464 and then probably go for the s366sxe.
  22. Replies
    20
    Views
    957

    Just thought id give an update, I now have full...

    Just thought id give an update, I now have full fuel to 4000 rpm. Now im working on getting my turbo to spool better, I wish I would have done more research before picking the s464 swap. Starting to...
  23. Lots of info in this forum, just need to take...

    Lots of info in this forum, just need to take some time and read through it. No one is going to hand you a tune for free, but there are quite a few tune files posted you can look through and get an...
  24. Replies
    5
    Views
    585

    Sorry I meant where did you locate the TPS with...

    Sorry I meant where did you locate the TPS with the dual pumps? I guess it is a question of if you have a auto or a stick? With the 03-04 auto the TPS is right where the second cp3 would mount.
  25. Replies
    5
    Views
    585

    What did you do with the TPS running dual cp3s?...

    What did you do with the TPS running dual cp3s? Also, turning 4200rpm what weight valve springs are you running? Looks like its running real clean, compared to my truck at least, good job!
Results 1 to 25 of 56
Page 1 of 3 1 2 3