Search:

Type: Posts; User: dhoagland

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    271

    If no body responds, Create a new post with your...

    If no body responds, Create a new post with your tune file and a log
  2. Replies
    11
    Views
    150

    Hmmmm... I'm wondering about Force motor...

    Hmmmm...

    I'm wondering about Force motor current/duty cycle, Input/Output/Speed sensors, ETC... For the Trans part...
    Then TPS, RPM, MAF, MAP, on the engine side.

    Beyond that maybe time to...
  3. Replies
    2
    Views
    47

    Post log and Tune

    Post log and Tune
  4. I was hoping you would jump in

    I was hoping you would jump in
  5. What Engine-PCM-OS-ETC... From what I understand...

    What Engine-PCM-OS-ETC...
    From what I understand some of the ECM with DRW do NOT have the internal drivers to drive an IAC
  6. Replies
    14
    Views
    121

    I see in your other posts you have your Cummins...

    I see in your other posts you have your Cummins tools now.
    In addition to trying to recover your ECM are you going to be able to try and re-flash (repair/recover) your TIPM too?

    Curious to see...
  7. Replies
    21
    Views
    194

    Really interested to see what happens here My...

    Really interested to see what happens here
    My boss is doing a similar install and I was concerned about different control modules not being present on the swap
  8. Replies
    1
    Views
    87

    You should be able to filter your graphs to not...

    You should be able to filter your graphs to not record that data.
    Maybe set to only log: TPS above 15% Or if there is a specific fuel trim cell used in decelerate..

    I'm not too good with filters...
  9. Replies
    2
    Views
    82

    I believe it has better internals: Faster...

    I believe it has better internals: Faster processor, more capacity, ETC...
    But I'm not expert on this
  10. Replies
    21
    Views
    194

    Sent you guys a PM

    Sent you guys a PM
  11. Ah.. Good to Know!!

    Ah.. Good to Know!!
  12. The plus and minus buttons on the tool bar

    The plus and minus buttons on the tool bar
  13. Replies
    21
    Views
    194

    Key switch have the same wiring? Could it be...

    Key switch have the same wiring?
    Could it be looking for something from a BCM module?
  14. Replies
    11
    Views
    150

    Do you have any logs?

    Do you have any logs?
  15. Poll: With your background and all the Tutorials and...

    With your background and all the Tutorials and Videos available I don't see any problems doing it yourself.
    And if you decide to change this down the road you can dial that in yourself.

    Only draw...
  16. Thread: 6.0 jeep

    by dhoagland
    Replies
    5
    Views
    89

    Yes That is what I did. Glad it worked out! I...

    Yes
    That is what I did. Glad it worked out!

    I was hoping I read your situation correctly. I know if you Originally had a 4L60 and Install an 80 there are harness and Pin out issues (custom after...
  17. It would be alot better if you post your Tune and...

    It would be alot better if you post your Tune and Logs
  18. Thread: 6.0 jeep

    by dhoagland
    Replies
    5
    Views
    89

    The drop down selector does nothing. I'm 99%...

    The drop down selector does nothing.
    I'm 99% sure you can do a segment swap. I found a Tune from an 02 Silverado with a 6.0 and a 4L80

    I segment swapped the transmission (Trans. Trans...
  19. Thread: 6.0 jeep

    by dhoagland
    Replies
    5
    Views
    89

    6L80? or 4L80?

    6L80? or 4L80?
  20. Replies
    2
    Views
    82

    Only way I have been able to do it is with an...

    Only way I have been able to do it is with an excel sheet.
    Here is one I did for looking at the % difference between 2 injection pulse width tables.
  21. I'm assuming you have to petal it to light off,...

    I'm assuming you have to petal it to light off, then it stays running.

    One of these has Cranking VE lowered (more overlap less efficiency)?

    One has Cranking VE Increased (more lift/duration...
  22. I'm not sure I added start up air flow, I think...

    I'm not sure I added start up air flow, I think thats what needs to be added too
    I'll look at the tune again
  23. Long MAF hz in your channels Try this as a...

    Long MAF hz in your channels
    Try this as a Starting point
  24. Replies
    2
    Views
    234

    Did the pull start after the new tires were...

    Did the pull start after the new tires were installed? I have seen "radial runout" on brand new tires.
    Swap front tire side to side and if pull follows the tire, well its the tire.

    How were the...
  25. Replies
    4
    Views
    267

    Yes Post up a log with your changes

    Yes
    Post up a log with your changes
Results 1 to 25 of 222
Page 1 of 9 1 2 3 4