Page 8 of 9 FirstFirst ... 456789 LastLast
Results 141 to 160 of 172

Thread: EEC-V Support

  1. #141
    Quote Originally Posted by Outlawz177 View Post
    What will need to get the beta just purchase the mpvi3 ?
    The beta software is on the downloads page on their website.

  2. #142
    Potential Tuner
    Join Date
    Dec 2019
    Posts
    3
    Hi Eric, is it possible to get the latest EECV firmware for RTD so it can be used with the RTD flasher?

  3. #143
    Potential Tuner
    Join Date
    Sep 2024
    Posts
    2
    I?m currently on the fence about converting my 86 fs bronco eecIV to an explorer EECV if there was full support for all 95-01 explorers. Don?t want to buy an external tranny controller and a separate engine control system. Maybe I missed it in this thread but are all 95-01 exploders covered now?

  4. #144
    Potential Tuner
    Join Date
    Sep 2024
    Posts
    5

    All v8 mustangs loaded

    Quote Originally Posted by Eric@HPTuners View Post
    This.
    So i purchased mpvi3 and downloaded beta it says failed then down below says interface not supported
    what do i do ?

  5. #145
    Potential Tuner
    Join Date
    Jul 2024
    Location
    Queen Creek AZ
    Posts
    7
    Quote Originally Posted by Eric@HPTuners View Post
    Today's build has support for 2003-2004 Mercury Marauder 4.6L 4V
    Great!! How do I get newer builds? besides whats in production?

  6. #146
    Do you have the beta software? If so, open it and go to help - about and check for updates.

  7. #147
    Quote Originally Posted by Outlawz177 View Post
    So i purchased mpvi3 and downloaded beta it says failed then down below says interface not supported
    what do i do ?
    When does it say it failed? Did you request the EEC-V firmware?

  8. #148
    Potential Tuner
    Join Date
    Sep 2024
    Posts
    5

    Beta

    Quote Originally Posted by jr2185 View Post
    When does it say it failed? Did you request the EEC-V firmware?
    Yes I have the beta version download where do you request for the EEC-v firmware?

  9. #149
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,480
    Quote Originally Posted by Outlawz177 View Post
    Yes I have the beta version download where do you request for the EEC-v firmware?
    via support ticket is your best bet.
    You can open a support ticket here https://support.hptuners.com/

  10. #150
    Potential Tuner
    Join Date
    Sep 2024
    Posts
    2
    Are all 95-01 5.0 explorers covered now?

  11. #151
    Potential Tuner
    Join Date
    Sep 2024
    Posts
    5
    I have dumb question on the 1999-2004 Mustang what timing selection to use for adding timing mainly wot I think it could use a couple degrees . On these there is not a high octane map I can see .

  12. #152
    HPT Employee Eric@HPTuners's Avatar
    Join Date
    Oct 2007
    Location
    Crawfordville, FL
    Posts
    2,545
    Quote Originally Posted by Outlawz177 View Post
    I have dumb question on the 1999-2004 Mustang what timing selection to use for adding timing mainly wot I think it could use a couple degrees . On these there is not a high octane map I can see .
    Borderline Knock is generally what you use to set the timing. However if MBT is lower than what you request, it will clip to that value.
    Eric Brooks
    HP Tuners, LLC

  13. #153
    HPT Employee Eric@HPTuners's Avatar
    Join Date
    Oct 2007
    Location
    Crawfordville, FL
    Posts
    2,545
    Quote Originally Posted by BWebb View Post
    Are all 95-01 5.0 explorers covered now?
    No, not all REAC3 and REAC4 strategies only currently (10.15.24)
    Eric Brooks
    HP Tuners, LLC

  14. #154
    Potential Tuner
    Join Date
    Nov 2019
    Posts
    1
    Ok , on the mpvi3 supported applications it still says that eecv is not supported in any capacity.

    Is this still the case or can I now buy a MPVI3 to tune a 03 Terminator?

  15. #155
    HPT Employee Eric@HPTuners's Avatar
    Join Date
    Oct 2007
    Location
    Crawfordville, FL
    Posts
    2,545
    Quote Originally Posted by Truedeal View Post
    Ok , on the mpvi3 supported applications it still says that eecv is not supported in any capacity.

    Is this still the case or can I now buy a MPVI3 to tune a 03 Terminator?
    Out of the box, if you hook up an MPVI3 to any EEC, it will tell you not supported until you get the EEC specific firmware.
    Eric Brooks
    HP Tuners, LLC

  16. #156
    Tuner in Training
    Join Date
    Jul 2020
    Posts
    16
    Hi Eric,

    possible to add this?

    KQTH7D2_OEM.hpt

  17. #157
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,480
    Quote Originally Posted by LUKAS98 View Post
    Hi Eric,

    possible to add this?

    KQTH7D2_OEM.hpt
    For tracking purposes would you be able to open a support ticket? We'd really prefer all of the new definitions to go through the proper channels.
    You can open a support ticket here https://support.hptuners.com/

  18. #158
    Tuner in Training
    Join Date
    Jul 2020
    Posts
    16
    why open support ticket, if i have no response ?

    i have do it for another def files like KQAH3T4, no answer...


    what do you think about this ?kqah3T4.jpg

  19. #159
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,480
    Your ford Focus definition is already in Eric's work in queue and we did respond as you can see in your screenshot.
    You can open a support ticket here https://support.hptuners.com/

  20. #160
    HPT Employee Eric@HPTuners's Avatar
    Join Date
    Oct 2007
    Location
    Crawfordville, FL
    Posts
    2,545
    Quote Originally Posted by LUKAS98 View Post
    why open support ticket, if i have no response ?

    i have do it for another def files like KQAH3T4, no answer...


    what do you think about this ?kqah3T4.jpg
    I'll get to it soon. I did probably 5 EEC-V definitions this week.
    Eric Brooks
    HP Tuners, LLC