I have a request to calibrate a 2016 6.4 scat pack truck. do we have access to those yet, and does the PCM need to be sent off for write access?
Phil
I have a request to calibrate a 2016 6.4 scat pack truck. do we have access to those yet, and does the PCM need to be sent off for write access?
Phil
I have an 2015 dodge charger R/T i want to get the PCM unlocked i just dont know the stock read number can i get some help??
I'm working with a 2015 Ram 1500 5.7 Sport and I'm trying to find a second PCM to send in for unlocking.
Is there a list of Mopar part #'s that are applicable for this?
I'd like to get this right the first time.
Thanks all.
Is there any way to verify the software version (GPEC2, GPEC2A) via the Continental PCM sticker? I see it says "2012-2016 Chrysler 200 3.6L" is supported, but there was a PCM change from 15 to 16. And with that change, even though the Chrysler part number is the same, there are two different Continental H/W numbers. Mine seems to be the oddball that has "11 bit" on the sticker, where all the PCM's I see on ebay, craigslist, etc.... are a different Continental H/W number, and doesn't have the "11bit" on the PCM ID sticker? Just want to be sure it can be supported before I go spending all the money.
I used the contact form to send support the link to the post 68, and a quick explanation of what's going on. Could not attach any pics so im waiting for the reply. Should i just post them here? One of the tag numbers is the vin, not sure if there's any negative aspect of posting it?
Mark, 1st of all THANK YOU for this post. Is there any chance we can get something like this for Ford and GM ?
Get on hptuners.com there is a list of every single car they support for every manufacturer.
pacificae.png
anything im doing wrong?, i puled the one IOP fuse same effect, on 60 amp DC power supply. i also manuallly selected the NGC3 from pull down same result, i also tried to read a 2006 G6 also failed? using v 3.6 and MVPI pro cable, i sware 7/10 times this HP tuners cable doesnt work read or support the OS or application, i must either have bad luck or HP missed supporting alot over the years.
Last edited by Sharmz; 12-28-2017 at 12:45 AM.
Please open a support ticket by emailing support. Include at least one infolog while attached to one of the vehicles in question. If you can obtain an infolog while connected to the 2006 G6 and the 2005 Pacifica, please send both.
For information on infologs, see: https://www.hptuners.com/forum/showt...acting-support
Any insight on supporting the 2018+ Jeep Wrangler 2.0 turbo ECU's soon?
I would be willing to donate some time towards testing/development. Or any other way I can help.
Mark, I realize this thread is rather old, but I wanted to thank you for providing all of these details, as the ECU/PCM information has helped me with a bunch of things I have planned for the future. Side bar you guys have done wonders for the Gen3 Hemi community.
2015 durango r/t 5.7
not reading
what ecm is this running?
15+ requires an unlock service from HpT
https://forum.hptuners.com/showthrea...Minor-Revision
What PCM type to use to read my 2020 Jeep Grand Cherokee Trackhawk 6.2L?
I tried a read entire and it took 9min 32 sec but not sure it read the TCM, not much info/tables in Trans section.
Do I need to buy license for TCM to read?
I'm trying to get a read so I can Purchase a new unlocked PCM from HPT and the site needs the me to send in a Read of stock PCM.
2020 Jeep Trackhawk, Functional Demon Ram Air Hood, AFE CAI, SW Headers, SW Cats, Solo Cat back Exhaust.
Hi. I have a Jeep Cherokee with a 2020 2.4 engine. I cannot determine the type of control unit. Can someone tell me? I assume that this is GPEC3. And another question, do you need to send a control unit from this car for revision?