I added a GM 2 Bar map to my car and want to log boost. Does anyone have the volts to PSI conversion for a GM 2Bar (12247571)?
Thanks
I added a GM 2 Bar map to my car and want to log boost. Does anyone have the volts to PSI conversion for a GM 2Bar (12247571)?
Thanks
2002 Quick Silver Z06 - Breathless Performance Shifter, DynaTech Headers SwainTech Coated, A&A Vortech Kit
0v = 0 PSI, 5v = 29.4 PSI, linear
2.4L Twin Cam Cavalier Z24 | T3 Super 60 @ 9 PSI | FMIC | TurboXS RFL | Greddy Profec B Spec II | Custom HO Intake Manifold | 2.5" Charge Pipes | 2.5" Downpipe | HP Tuners | 5 Speed Swap | Team Green LSD | SPEC Stage 3 Clutch | Fidanza Short Shifter | Prothane Control Arm Bushings | Carbon Fiber Hood
Isn't a 2 bar only 15PSI? so would it be 0v-0PSI and 5v-15PSI?
Thanks
2002 Quick Silver Z06 - Breathless Performance Shifter, DynaTech Headers SwainTech Coated, A&A Vortech Kit
No, 2 bar is 29.4 PSI, the first 14.7 psi is negative (atmospheric pressure is 14.7 PSI give or take depending on altitude), so from full vacuum to WOT on an NA car is 0 to 14.7, which is where boost gauges usually read 0psi (psig, above atmospheric).
2.4L Twin Cam Cavalier Z24 | T3 Super 60 @ 9 PSI | FMIC | TurboXS RFL | Greddy Profec B Spec II | Custom HO Intake Manifold | 2.5" Charge Pipes | 2.5" Downpipe | HP Tuners | 5 Speed Swap | Team Green LSD | SPEC Stage 3 Clutch | Fidanza Short Shifter | Prothane Control Arm Bushings | Carbon Fiber Hood
Thanks, I'll try it tonight.
2002 Quick Silver Z06 - Breathless Performance Shifter, DynaTech Headers SwainTech Coated, A&A Vortech Kit
It's a PID in the EIO section of the scanner. Look under MAP & the GM 2bar is listed.
Always Support Our Troops!
The 2 bar in the EIO section maps KPA not PSI.
2002 Quick Silver Z06 - Breathless Performance Shifter, DynaTech Headers SwainTech Coated, A&A Vortech Kit
actually it starts at 9kpa..and goes to 198.65ishOriginally Posted by Shifted
1.3054 ~ 28.8122 psi range
volts/0.18177 + 1.3054
that should get you PSI
or you can use the one already preset and its set up to be 2 bar map...
then you can calculate PSI by doing
[pid for 2 bar map]*0.14504
that will also be PSI
-Scott -
Quote
or you can use the one already preset and its set up to be 2 bar map...
then you can calculate PSI by doing [pid for 2 bar map]*0.14504 that will also be PSI
The problem I'm having is finding the PID for the 2 Bar Map on EIO Input #3
Thanks
2002 Quick Silver Z06 - Breathless Performance Shifter, DynaTech Headers SwainTech Coated, A&A Vortech Kit
see picture below...
right click your EIO input 3 in the scanner....
click "insert"
double click the 2 bar PID
-Scott -
or are you talking about my "[pid for 2 bar]"Originally Posted by Watch22
to get that you have to have a 2 bar OS in your vehicle..then you add 2 bar map in the table display..it will appear under engine-airflow-just like the 1 bar map does..it should appear right below that...
-Scott -