We do not support Focus ST currently, it is in the works though.
We do not support Focus ST currently, it is in the works though.
Eric Brooks
HP Tuners, LLC
Trying to read a 2015 F Series/6.2, but keep getting a negative response code when trying TC-1791/97. Any Ideas? I have E-Mailed Support as well.
Thanks again for your hard work Eric, what HP has been doing with the Ford platforms is good stuff!
'17 Whipple'd S550
Too many other projects to list.....see my YouTube channel for more: https://www.youtube.com/channel/UCr7...-XfDG53sCh6tcw
What about a 2008 F450 with 6.4 diesel and manual trans?
2010 Vette Stock Bottom LS3 - LS2 APS Twin Turbo Kit, Trick Flow Heads and Custom Cam - 12psi - 714rwhp and 820rwtq / 100hp Nitrous Shot starting at 3000 rpms - 948rwhp and 1044rwtq still on 93
2011 Vette Cam Only Internal Mod in stock LS3 -- YSI @ 18psi - 811rwhp on 93 / 926rwhp on E60 & 1008rwhp with a 50 shot of nitrous all through a 6L80
~Greg Huggins~
Remote Tuning Available at gh[email protected]
Mobile Tuning Available for North Georgia and WNC
Anything promising on the Focus ST support?
Or news on the Fiesta (non-ST)?
2013 ford police interceptor sedan 3.5 FWD (Taurus)
Correct. It was an option for FWD with NA 3.5
I just saw the email from support that suggested either tri core or esys. Last time I was messing around and just starting from top of list for ford and work my way down and ended up got check engine light for commutation error and system incompatible
But have not try two suggested yet.
How About 2012 Ford Taurus ??
All of the non-ecoboost 3.5s I have ran across so far use the ESYS PCM
Eric Brooks
HP Tuners, LLC
Is there a protocol for 00 v10 ?
I'm trying to connect to 2 Raptors, years 2014 and 2010.
I'm having trouble to read that stock 2010 tune. None of the Ford hardware options seem to connect.
2010 Ford F-Series, 6.2 L, 8 Cyl
ECM: 7E8, CAN, PIDs: 42
Calibration IDs: BBGN8J5.H32
Pending Trouble Codes:
Trouble Codes:
Permenant Trouble Codes:
Scanning Methods: Mode 0x01 Functional, Mode 0x01 Physical, ISO 14230-3 Mode 0x22 None, Mode 0x23 4x2
First I had the same issue with that 2014 model but after some trial and error I noticed that after every failed attempt I had to re-open editor for some reason. Finally I got the tune to my laptop by choosing the Copperhead hardware.
2016 F150 Eco Boost?
Eec-v?
Trying to read a BA XR6t won't recognise controller and none of the ones I've tried are working. Either I get a checksum error, can't save the file on completion or it encounters an error during reading. Using the new software.
I have a 2016 Ford F250 with a 6.2L but wasn't sure which ECM to choose. It showed BRBU1A7 code if that helps.
Tried to read a 15 mustang auto, got MGMBAG5 read in 2 seconds but did not open or Identify the controller type.
Any Help on this car is not in my possession after this post customer had to leave.
I sent support a ticket but that I thought I would ask here. 2008 F150 w/ a 5.4
Which PCM ID? I thought someone on here might know. Thanks.
Last edited by Jay@HAP; 06-10-2016 at 02:31 PM.