Results 1 to 10 of 10

Thread: calibration write not completed

  1. 10-19-2015 #1
    lq4s10
    lq4s10 is offline
    Potential Tuner
    Join Date
    Oct 2015
    Posts
    6

    calibration write not completed

    Hi my name is Ramiro.
    I am a newbie and hope to learn a lot. I just got my 2.24 version and removed vats and a few other changes on my 93 lq4 swapped Silverado. Everything went smooth but now I'm trying to write my friends tune which is just deleting VATS and manual trans. When I go to write the calibration it goes through the list of gathering info, validating, requesting access, prep vcm, writing cal, validating.....then the status bar for VCM write completed in 0:31 scrolls across as finished but it doesn't actually make the changes. the window just stays open. The cable status then shows disconnected.
    I tried searching, I find a few posts but no solution.
    I tried restarting program
    restarting laptop
    unplugging and restarting interface.

    A little info
    I have the standard version
    its a 2001 5.3, th400 trans
    hp laptop, windows 8
    it will read ecm but no changes or errors shown

    thanks in advance
    Reply With Quote Reply With Quote
  2. 10-19-2015 #2
    Bill@HPTuners
    Bill@HPTuners is offline
    HP Tuners Support
    (foff667)     Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,774
    Sounds, to me, like the changes took just fine. After it passes the erase point the calibration is erased, then it flashes in the new calibration.
    You can open a support ticket here https://support.hptuners.com/
    Reply With Quote Reply With Quote
  3. 10-19-2015 #3
    lq4s10
    lq4s10 is offline
    Potential Tuner
    Join Date
    Oct 2015
    Posts
    6
    That's what I thought but when I go to start it, it just runs for a second and shuts off. I swapped the ecm with VATS deleted from another vehicle to verify and it will start and run.
    Reply With Quote Reply With Quote
  4. 10-19-2015 #4
    5FDP
    5FDP is offline
    Tuning Addict 5FDP's Avatar
    Join Date
    May 2012
    Location
    Rogers, MN
    Posts
    14,066
    So you tried to a write a different tune to your cars computer?? Like took his file and then wrote calibration only to yours?

    If so, that won't work.

    You need to see if your OS can have a segment swap done to manual trans then delete the VATS off the pcm in your vehicle.
    2016 Silverado CCSB 5.3/6L80e, not as slow but still heavy.

    If you don't post your tune and logs when you have questions you aren't helping yourself.
    Reply With Quote Reply With Quote
  5. 10-19-2015 #5
    lq4s10
    lq4s10 is offline
    Potential Tuner
    Join Date
    Oct 2015
    Posts
    6
    No, each comp has its own file. Each one is licensed. I used my ecm to just make sure everything was good on his s10 to verify no low fuel pressure or mechanical problem.
    Reply With Quote Reply With Quote
  6. 10-19-2015 #6
    lq4s10
    lq4s10 is offline
    Potential Tuner
    Join Date
    Oct 2015
    Posts
    6
    Tried to write again. It will go till the end and just stops. Maybe someone has had this problem.
    We are trying to get this thing down the local track to do its first test run on saturday. Maybe start working the bugs out once we can get it running.

    http://m.youtube.com/watch?v=RBP9xkDJvcA
    Reply With Quote Reply With Quote
  7. 10-19-2015 #7
    Bill@HPTuners
    Bill@HPTuners is offline
    HP Tuners Support
    (foff667)     Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,774
    Its working properly. I watched the video.
    You can open a support ticket here https://support.hptuners.com/
    Reply With Quote Reply With Quote
  8. 10-19-2015 #8
    5FDP
    5FDP is offline
    Tuning Addict 5FDP's Avatar
    Join Date
    May 2012
    Location
    Rogers, MN
    Posts
    14,066
    Yup, that write is 100% complete.

    See how it says "close" that means the write is done aswell.


    Post the tune here if you are still having issues, maybe something was not changed right.
    Last edited by 5FDP; 10-19-2015 at 10:25 PM.
    2016 Silverado CCSB 5.3/6L80e, not as slow but still heavy.

    If you don't post your tune and logs when you have questions you aren't helping yourself.
    Reply With Quote Reply With Quote
  9. 10-19-2015 #9
    lq4s10
    lq4s10 is offline
    Potential Tuner
    Join Date
    Oct 2015
    Posts
    6
    Ok I will post them as soon as I can. I really appreciate both of your help. Its probably something simple, I hope.
    Reply With Quote Reply With Quote
  10. 10-20-2015 #10
    lq4s10
    lq4s10 is offline
    Potential Tuner
    Join Date
    Oct 2015
    Posts
    6
    I think I figured out what is wrong. The ecm I am using is from a 2002 escalade. The connectors on the ecm are red and blue and I was under the assumption that it would be DBC. Until I remembered that escalades came with DBW. Am I correct???? When I scanned it yesterday I noticed all was showing activity on the (VCM scanner) gauges except the TPS. How do I change the VIN or is it possible. I figured its a 411 ECM so it should be possible.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »