2005 Cummins 325/600 G56 3.73
Reving to 4800
Worked Head, Twin Disc, BBI
Did you email him or pm him? He requested you email him.
He is a busy guy and he seems to prefer email. If that is easier for him and he is willing to help then so be it. Looking forward to hearing his suggestions.
I'm pretty interested in hearing results to this, as well.
Considering that my truck was one of the guinea pigs for the Beta testing during the last quarter of 2015 in the hands of a very competent Diesel tuner, and the fact that he shared information with me in regards to the progress HP Tuners was making in knocking down the RPM limiters, I find it interesting that Les mentioned he has had no issues with revving an 05 out to 5K RPM when the tuner/beta tester who had my truck mentioned HP Tuners was, and still is, trying to figure out what was/is limiting the 2005 trucks from revving out.
My truck hits a hard limiter around 4200 RPM, starts shuddering like crazy. Almost feels like it's popping in and out of gear at a high frequency when it does it (auto trans).
Last edited by B00STJUNKY; 04-20-2016 at 01:56 PM.
There has to be logic in the computer for cam/crank sensor error detection, like a maximum frequency value, as well as a maximum frequency delta per time, as least on early 04 trucks and 03 trucks. They will pop like you are hitting a rev limiter if the truck breaks loose in the rain in low gears and a "snap rev" occurs. And its not necessarily at a certain RPM. I wonder if the limitation is something like that? I know on fords there's a value called minimum PIP per rev, that causes this exact issue.
Your truck might just be floating the valves :-)
Last edited by Turbo_Mike; 04-20-2016 at 02:34 PM.
2003 305/555 QCSB Cummins
Piston/rod/sleeve/fire ring/dual CP3/300 overs
Super Stick NV5600
S366/S480
Kind of doubt that with 110# springs installed.
You can see the commanded fuel just drop like a rock in the logs at that RPM, as well. All available fuel limiters are well above where it drops off, so I know that torque/boost/air density/baro/low fuel press. limits are not what is holding this thing back.
If such cam/crank error detection parameters exist, they aren't currently defined in the calibration. Unless I've missed them. I'll double check, but I don't believe they're there.
Last edited by B00STJUNKY; 04-20-2016 at 03:06 PM.
Any of you modify ECM 7439?
If so, return to stock and report back your findings.
2003 305/555 QCSB Cummins
Piston/rod/sleeve/fire ring/dual CP3/300 overs
Super Stick NV5600
S366/S480
new VCM suite has Additional Governors now, and explanations for each one. Finally!!! revs to 4500 no problem. I did change back what les mentioned too. I will change it back to what i had it before and see if it has the issue still.
2005 Cummins 325/600 G56 3.73
Reving to 4800
Worked Head, Twin Disc, BBI
I attempted leaving the table Les mentioned modified with the new High Speed Governor settings altered for higher RPM, and still ran into the injector cutout at 4200 RPM.
Reverted table 7439 back to stock, and it revved to 5k with zero issues. Weird that the table doesn't function properly...
Thanks for the hint, Les! Much appreciated!
How did you have table 7439 modified?
That seems odd that raising EOI to 42* would cause your problem? Hey, Les would you be willing to help us understand how increasing EOI to 42* would cause these problems? I am having a tough time understanding how extending this out to 42* at higher RPM would cause this? I have been doing a lot of research on the EOI and could see a lower number be a issue with higher duration but not a higher number? I have been using 42* in this table equivalent with efilive on the 06-07 trucks.
I have no idea why with HPT the modification of this table to 42* does what we are seeing.
I agree that ALL of my 5.9 Efi live tunes are set to 42* with no ill effect.
Thank you for sharing your findings!
I know this thread is old but I'm getting a unknown 00:3e? Anybody know?
I keep gettin a "idle low speed gov" anybody have an idea on how to get rid of it ?
Yea , till around 1300 rpm