VCM Suite 3.0 Is Finally Here!!!

[HackAbuse]

Try reading it, I would start with the esys ecm type, if that doesn't work go through the others to see if you can get it to pull the file. Once done send the read & a vcm suite infolog to support at hptuners.com

Sounds good, thanks for your quick response. Really hoping we can get him squared away this evening, but if not, no biggie.

Also, is the Allison A50 TCM something being considered for support? I have a 2013 Duramax to do in the morning and the customer would like to get his transmission done sometime in the future if possible.

[yonson]

DoD status bits should be available in tomorrows 3.1 BETA

Thanks, now we just need log marks...

[mowton]

Not sure when it happened but I am sure as of last week all was working ok. Tried going back to 97 and 303 with no luck. My Pavillion Desk top (all in one) is working fine...just can't get it to the car to test the new serial WB beta :-(

Anyone else having issues?

Ed M

[HackAbuse]

Try reading it, I would start with the esys ecm type, if that doesn't work go through the others to see if you can get it to pull the file. Once done send the read & a vcm suite infolog to support at hptuners.com

I was able to pull the file using the TC-1791 protocol without issue - Just shot the file over to you guys for definition updates. Thanks again for your support! My customer is dying to get his tune down now

[strokedTA]

Can't wait to buy a holley efi!

[gols1go]

Just got a new tablet with windows rt 8.1. Tried installing 3.0 but with no success. Is this possible. I tried searching for the drivers but I cannot seem to locate the ones for this version of windows.......

[Keith@HPTuners]

Windows RT is not supported.

[gols1go]

Just got a new tablet with windows rt 8.1. Tried installing 3.0 but with no success. Is this possible. I tried searching for the drivers but I cannot seem to locate the ones for this version of windows.......

Thanks. I guess it's back to the laptop.

[2therock]

When flashing the ecm & tcm, after the tcm completes it says "cycle the ignition". Does this mean start the engine? Or cycle the switch?

Thanks

[usc45cal]

great

[5_Liter_Eater]

I guess cylinder balance test is gone now?

[Keith@HPTuners]

That will likely be added in the VCM Suite 3.3 release.

[5_Liter_Eater]

That will likely be added in the VCM Suite 3.3 release.

But but...

Nothing was removed from 2.24 to 3.0...

Also, the injector disable function doesn't work on my E40. But no biggie as I'm used to stuff not working on the bastard child spawn of satan PCM

[Bill@HPTuners]

But but...





Also, the injector disable function doesn't work on my E40.

You are quoting me out of context dude.

That post was in regards to a maf table the guy thought was missing several pages back...has nothing to do with RTT, scanner features, etc. It had to do with the table the guy was referring to.

[HackAbuse]

Really hoping 2016 Ford 3.7L support for Mustangs comes out soon, this guy is bugging the hell out of me to do his car lol

[HackAbuse]

Really hoping 2016 Ford 3.7L support for Mustangs comes out soon, this guy is bugging the hell out of me to do his car lol

I know there's no ETA on this, but is it at least being worked on? I'm about to lose an important customer over this because we are both completely in the dark.

[Bill@HPTuners]

Have you tried reading it? That would be a good first step.

[HackAbuse]

Have you tried reading it? That would be a good first step.

Yeah I read and sent the file in a little over a week ago, ticket #36727. Haven't received any responses to my emails yet other than the initial reponse saying that the file was passed up to an engineer

Thanks for your quick response

[Bill@HPTuners]

In that case we have no eta.

[HackAbuse]

I know there's no ETA on this, but is it at least being worked on? I'm about to lose an important customer over this because we are both completely in the dark.

In that case we have no eta.

I'll let the customer know