2013+ ZF8 8-Speed Now Supported - VCM Suite 3.5 Beta

[[email protected]]

in "D" after manually paddling down while still in "D" it'll shift at about 6800-6900rpm!!

Good info! I didn't try this. Otherwise my experience was the same as yours - modified shift points only seem to work in drive. Manual and TUTD (paddle shift) do not seem to be using the provided tables. I'll try throwing it in "D" and then paddle it like you indicated.

[Monzsta]

On the dealer side of things we can view four categories of information for each clutch. This is useful to see how things are getting along. Will there be any way to see data in the scanner such as clutch fill data, shaft speeds and converter slip rate?

Here's a screenshot of OEM data.

1C6RR7FG7ES216733 8HP70 CLUTCH FILL DATA P0734 4TH GEAR RATIO.png

[uarperformance]

Pulled a 14 Charger RT with latest BETA. It only showed the 8 speed and would not read the trans data.

[Lidio Iacobelli]

I've got a local guy who is kinda loyal to the whole "Diablo" thing (multiple tunes and Bla Bla) with respects to tuning on the motor side of things,, but he already heard and seen what I've done with mine in the last day or so with bumping up the shift RPMs and etc,, and hopefully eventually get the shifts firmed up to chase bigger power in the future.

My question is; will it be possible to leave his Diablo tunes and PCM alone,, and only unlock and edit his TCM with HP-tuners?

Thank you

[[email protected]]

I've got a local guy who is kinda loyal to the whole "Diablo" thing (multiple tunes and Bla Bla) with respects to tuning on the motor side of things,, but he already heard and seen what I've done with mine in the last day or so with bumping up the shift RPMs and etc,, and hopefully eventually get the shifts firmed up to chase bigger power in the future.

My question is; will it be possible to leave his Diablo tunes and PCM alone,, and only unlock and edit his TCM with HP-tuners?

Thank you

Yes, I have tested this and there is no issue.

[Lidio Iacobelli]

Thank you !

[GPGTP]

Would anybody be willing to post a stock read with the trans tables so I can look them over?

[ElecTech]

Pulled a 14 Charger RT with latest BETA. It only showed the 8 speed and would not read the trans data.

Your InfoLog shows that you are not connected to a vehicle or interface.

[[email protected]]

Would anybody be willing to post a stock read with the trans tables so I can look them over?

I just upload a stock 16 Scat Pack TCM read and a stock 16 Hellcat read to the repository. Once HPT approves them they should be available.

[26sutphen]

Will this support the zf that is in the 2015 Ram 1500 with the ecodiesel? Thanks in advance..

[Mark@HPTuners]

Will this support the zf that is in the 2015 Ram 1500 with the ecodiesel? Thanks in advance..

Yes it should the TCM in your truck. If you already have VCM Suite and an MPVI, try reading it out.

Just note, we do not support the ECM that is in the RAM 1500 Ecodiesel.

[fasthemiram12]

Anyone care to share what they've figured out works or doesn't?
Id hate to go in and melt down my trans blind...

[[email protected]]

Anyone care to share what they've figured out works or doesn't?
Id hate to go in and melt down my trans blind...

We have tested converter locking and unlocking and modifying shift points at WOT - remember that the RPM's listed in the shift tables are output shaft RPM (like the A580).

[Steven@HPTuners]

Would anybody be willing to post a stock read with the trans tables so I can look them over?

Here's a read of my Hellcat for you.

[aak426]

i read the tcm on my 2014 ram 1500 5.7 but the file seems not right and would crash if select some of the stuff and others are unusable , so i tried to read the whole thing but by the end it just stopped .

anyone had similar problem ?

[Mark@HPTuners]

i read the tcm on my 2014 ram 1500 5.7 but the file seems not right and would crash if select some of the stuff and others are unusable , so i tried to read the whole thing but by the end it just stopped .

anyone had similar problem ?

Please send the file to support.

[aak426]

Please send the file to support.

here

[Mark@HPTuners]

here

Please send the file to support by emailing it to support at hptuners dot com. This way, it generates a support ticket with the file and we can keep all the information in one place.

[Stevo]

Here's a read of my Hellcat for you.

Thanks!

[WS6HUMMER]

Anyone figure out how to make them shift firmer? I'm looking and thinking oncoming clutch pressure?