Page 2 of 2 FirstFirst 12
Results 21 to 28 of 28

Thread: Pulling KR timing on WOT

  1. #21
    Tuner in Training biggmac4's Avatar
    Join Date
    Nov 2012
    Posts
    34
    Will do
    2013 Challenger R/T, forged 392 stroker, 5.7 block, TR606 6-speed, TorqStorm supercharger, intercooled, 5psi, Getrag 3:73 rear end.
    1992 Foxbody GT, 6.2L LS3, Procharger F1-A, Tremec TKX. Meth Injection

  2. #22
    Tuner in Training biggmac4's Avatar
    Join Date
    Nov 2012
    Posts
    34
    Quote Originally Posted by PurpleRam View Post
    1st question is which Alloy ? 2618 or 4032? 4032 pistons are quieter , looking at the Zeros log your Idle at 180F is quiet , hovers around .35+/-v so I'm guessing 4032s (I could be wrong)

    I do tuning for a guy who has a Drag pak clone (and a real 2015 DP car) 354 ci all forged with 2618alloy pistons, car runs a 2015Hellcat ECU , at WOT it'll pull as much as 2.5-3.5v at 180f operating temp, at 165f operating temp (160F t-stat) it pulls 3.0-3.75v@ WOT . During warm up it's LOUD idling at 1.5-1.6v no matter the T-stat. once it gets to 180 it's around .65+/- .10v @160f it's .90+/- .15v

    Looking at your log zeros your fine with a 2.5v min, I'm going to take the Tune you posted earlier in this thread and rework it , it'll be close to what you have but I'm going to change some things that I can't explain here and my dam Phone broke today so I can't do a Video like what I did for the Ram/VVT thread .
    2618,s

    "SCAT 5. 7 TO 6. 4 HEMI STROKER KIT #1-48507BI- + H-BEAM RODS *.030 OVER PISTONS, KIT TO INCLUDE: ICON 2618 PREMIUM FORGED PISTONS -21. 2CC HASTINGS STEEL MOLY PISTON RINGS SCAT 4340 FORGED STEEL CRANKSHAFT SCAT 4340 FORGED H-BEAM CONNECTING RODS W/ ARP 7/16 CAP SCREWS CLEVITE H-SERIES HEAT TREATED MAIN BEARING SET CLEVITE H-SERIES HEAT TREATED ROD BEARINGS"
    Attached Files Attached Files
    Last edited by biggmac4; 09-22-2023 at 04:51 PM.
    2013 Challenger R/T, forged 392 stroker, 5.7 block, TR606 6-speed, TorqStorm supercharger, intercooled, 5psi, Getrag 3:73 rear end.
    1992 Foxbody GT, 6.2L LS3, Procharger F1-A, Tremec TKX. Meth Injection

  3. #23
    Senior Tuner
    Join Date
    Jan 2022
    Location
    fountain valley
    Posts
    1,321
    what is -21.2cc?

    how much static did that create running whatever head gasket you run?

  4. #24
    Advanced Tuner PurpleRam's Avatar
    Join Date
    Aug 2017
    Location
    Quakertown PA
    Posts
    483
    Quote Originally Posted by LilSick View Post
    what is -21.2cc?

    how much static did that create running whatever head gasket you run?
    21.2cc dish piston with a .040 head gasket, it's roughly 9.30 to 1(with 3.927 bore,9.4 to 1 3.947 bore) .028 and 3.927 bore it's roughly 9.6 to 1 . .035 head gasket and it's in the 9.30s ball park.

    If those were +21.2CC dome pistons ...... Whoooo Boy we'd be looking at 16ish ( I have 20.5CC dome 4.0X3.9 G3 with AFR 72CCs sitting on the floor 14.7 to 1....Now that's some fun.)
    04 RAMGTX........ 8.91@151mph 392Ci G3Hemi 3600lbs 2.6HP/Ci Naturally Aspirated
    05 RAMGTxtreme 9:45@142mph 426Ci G3Hemi 4000lbs 2.2HP/Ci Naturally Aspirated
    09 Challenger Drag Pak 8.88@150mph 376Ci G3hemi 3650lbs 2.6HP/Ci Naturally Aspirated
    G3 Hemi Videos

    https://www.youtube.com/channel/UClS...5mXdDR5sOxs10Q

  5. #25
    Tuner in Training biggmac4's Avatar
    Join Date
    Nov 2012
    Posts
    34
    Yes sir dish pistons with .028 thick gasket
    2013 Challenger R/T, forged 392 stroker, 5.7 block, TR606 6-speed, TorqStorm supercharger, intercooled, 5psi, Getrag 3:73 rear end.
    1992 Foxbody GT, 6.2L LS3, Procharger F1-A, Tremec TKX. Meth Injection

  6. #26
    Tuner in Training biggmac4's Avatar
    Join Date
    Nov 2012
    Posts
    34
    I attached the voltage log a few post up.
    2013 Challenger R/T, forged 392 stroker, 5.7 block, TR606 6-speed, TorqStorm supercharger, intercooled, 5psi, Getrag 3:73 rear end.
    1992 Foxbody GT, 6.2L LS3, Procharger F1-A, Tremec TKX. Meth Injection

  7. #27
    Senior Tuner
    Join Date
    Jan 2022
    Location
    fountain valley
    Posts
    1,321
    Quote Originally Posted by biggmac4 View Post
    Yes sir dish pistons with .028 thick gasket
    ya'll are way too trusting

    i dont give a fuck what it says on a piston box or a cam card...

    i measure EVERYTHING



    and guys are wondering why they are having issues fml

    did you measure the valve to piston or the pushrods (where the plunger ended up)?
    Last edited by LilSick; 09-22-2023 at 05:37 PM.

  8. #28
    Senior Tuner
    Join Date
    Jan 2022
    Location
    fountain valley
    Posts
    1,321
    well...

    you built a supercharged engine and are running it on gasoline

    no idea what .0305 is...

    but there is something called effective compression ratio which is determined but stuff that gets measure

    it can have something to do with this knock issue you have just identified