2011 Camaro 2SS Convertible L99 Bone Stock for now
2003 Dodge 2500 5.9 Cummins QC 4x4. Airaid, 2nd Gen Intake, Grid Heater Delete, D-Tech 62/65/12, Magnaflow. Bully Dog: Propane Injection, Triple Dog W/Outlook Crazy Larry. Edge EZ, BD Flow-Max, 48RE: Sonnax Sure Cure/Transgo combination, Derale turbulator, billet input, Triple Disc, Super servo, 4 ring Accumulator. :beer
This guide was very helpful. A couple things I noticed. After getting fueling right, idle speed (750 idle rpm), and timing (20 degrees at idle); I zeroed out my base running airflow table and logged the dynamic airflow for each idle rpm in park and in gear. I then pasted 80% of the value into the table and smoothed it out down and up RPM. I then turned my idle adaptive back on and used the spark correction to dial in the table. I noticed as I got the base idle airflow table dialed in the adaptive spark corrected less and less. Once it was down to 1 degree or less correction I was happy.
I have a BTR Stage 2 LS3 cam that has some chop. With factory spark and air idle corrections I was getting rpm swings back and forth. Controls were too tight. I cut the idle spark correction settings in half, airflow corrections aboout 70% of original, kicked up proportional corrections to 75 rpm, and it idles much smoother. The car stopped correcting for the cam lope and allows it to lope naturally now. Some people like the chop chop chop sound and may want to purposely let a tight idle correction swing back and forth to get that cam sound. I admit. It sounds good. But I am trying to hide the cam and be a sleeper so I muted the adjustment. I could have also dropped the idle speed down to 700 or 725 to get more chop sound.
One other issue I had is coming to a stop the idle would dip too low. The trans was pulling timing for the 2-1 downshift just as I was coming to a stop causing the engine to fall on its face. I left the CT downshift on and raised the 2-1 downshift to 8 mph which elminated it.
Between my remote tune which was fantastic for power and me dialing in my idle the car is a dream to drive now. It really helped to make a change, log the idle (letting my changes settle out and injector tip temp to come back down after reflash), and see how my adjustments changed how the car adapts/changes the idle.
Is there a trick to getting the RPM error graph to populate? Nothing shows up on my graph or chart. I'm using the files bigmike42 posted early on.
I got the car to Idle perfectly and found the best smoothest Idle to be around 9.5 g/s around 22 and 24 degrees of spark. however it just won't drop to my target Idle, I have tried targeting idle on 800 but the actual reading is 1,000 ~1,150 rpms I have even tried raising/lowering Min airflow & spark tables but no matter what I try the Rpm won't drop below 1000 rpms.only way I could drop it is by raising the ETC AREA SCALAR, now keep in mind that with the stock setting it wouldn't drop RPM below 1,500 rpm for some reason.
The car was previously tuned by 2 tuners while power was great, Idling and drivability were crappy.
6.9L stroked LS3
10.5:1 CR
ported heads
BTR Stage 3 NA Camshaft Specs: 239/254 .631"/.610" 114+3
6.2L denali Intake Manifold
90mm Silverblade TB
2010 Camaro Injectors
engine is swapped FYI
I attached a log of the latest tune, I know there is much to do in the tune but I am taking it in small steps.
Starts up fine, No issues and did around a bit of maf tuning (Car still runs open loop MAF only in attached tune) once I dial in this Idle issue and make sure its no longer surgin on Idle/Roundabout/AC on then I will finish up the MAF and move over to VE tuning.
Would Appreciate any suggestions instead of me messing with the ETC Scalar and any tips to get this done.
Thanks.
Seems something is amiss with my step 1 file. I set what I knew from Mikes first post, but I still have to lightly pedal the engine to keep it going. It doesn't seem to matter what I put in the base airflow.
What did I miss? It sounded so simple.
step 1 IDLE CONTROL.hpt
This is the best it will do. doesnt seem to matter how much spark or airlow minimum, it barely idles.
idle test.hpl
It seems that Throttle is always at 7.1% and it wants to die
EDIT:
07GTS's post #160 seems to help tremendously. Proportional airflows back to original and not zeroed out fixed the issue. Now I can tune. I guess I misunderstood what needed zeroed or it doesnt work with the E67.
"your base running airflow v ECT mult is zeroed out try that back to stock, and ALL your "follower torque" is zero too that wont help at all go back to stock, and all your adaptive airflow corrections are zeroed out that means that the ect isnt going to help at all, to dial in idle airflow put all those airflow tables back to stock and then zero out the spark correction tables and set idle spark tables to all the same say 16 then main spark to all 16 also so idle spark stays steady, then see what its like and adjust the airflow tables to dial it in and then once its good use spark as the last help (spark correction should be minimal if airflow is setup correct) also with those spark correction numbers maby try halving them"
Last edited by marksrig; 01-22-2023 at 06:45 PM.
Just did this today. I can usually get close just stumbling through but i was having a shudder (lots of misfires) Whenever I had a timing dip. Set my timing locked to 20*, was able to knock 50 rpm out of my idle speeds and dialed it in in about an hour. Used the CTSV airflow numbers. Misfires changed to 1-4 here and there which is just the larger cam im sure. So i desensitized that and it runs beautifully.
Just found this thread today. I changed my tune with the changes you listed, and bingo all is well. GMC 2012, 5.3 w/btr Truck Norris cam and springs, 6l80-tuned. The transmission still has a slam shift 6-3 and 6-2 I think!
I know this is an old thread, but the idea of zeroing everything out is so that there is nothing controlling the throttle blade or ignition timing during idle "while" your are trying to find the min idle setting in this procedure.
That's why it wants to die. I found with mine, if you just lightly pedal the throttle for 20-30 seconds it would stay running unless your min air settings are to low.
You need to pay attention to the RPM error and that is your indicator for min air flow.
One thing I found is the min air flow is not to far off what the MAF sensor reads at an engine idle when hot.
Once you have figured out min air, then put all the tables back the way you had them before or stock as 07GTS said.