Truck has a btr stage 2 cam.
Truck has a btr stage 2 cam.
Well, judging by the wealth of information you've provided, looks like it has split fuel trims. If the ONLY modification to the vehicle is a BTR stage 2 cam, looks like you has some problems.
You might want to let it get up to operating temp before you get too wrapped up in what it's doing when it's cold.
EFI specialist
Advanced diagnostics, tuning, emissions
HPtuners dealer and tech support
email=[email protected]
Gimme a few and I’ll update
Tune file and log is in attached, purchased this truck off of a guy with just idea that it ran but not good clearly. Appreciate the help!
Your pid list is terrible. Use the attached channel list for data logging. If you don't know how, search how to download, save and open a channel list.
Bank 1 fuel trims are pegged positive which means it's adding as much fuel as it can on that side. You don't have O2s in your data so I can't see what they look like but I'd bet you have a bad O2 sensor or the whole bank is dead, something like that.
Do you have a temp gun? Infrared point and shoot temp gun? If not go down to Harbor Freight and grab one. They're cheap nowadays. Need to check your exhaust manifold temps.
Bottom line you need to figure out why bank 1 has the trims maxed. There's no tuning that will fix that.
P01 DBC.Channels.xml
EFI specialist
Advanced diagnostics, tuning, emissions
HPtuners dealer and tech support
email=[email protected]
Do I need to buy credits to flash this thing back to stock to see any change?
That depends how you want to approach that. But flashing it back to stock won't fix your split fuel trims. I'm telling you that's not something that can be fixed by tooning. Put your laptop and interface down and figure out mechanically what's different between the banks. It's bad so it should be pretty obvious.
EFI specialist
Advanced diagnostics, tuning, emissions
HPtuners dealer and tech support
email=[email protected]
EFI specialist
Advanced diagnostics, tuning, emissions
HPtuners dealer and tech support
email=[email protected]
Okay I got it back but that bank is still not producing,O2 sensors are working. Short term bank 1 still maxing out and long terms are doing nothing.
I’ll break into it when I get home and see what I see.
Alright new plugs and new o2 sensors here is a log.
P0036 - HO2S Heater Control Circuit (Bank 1, Sensor 2) (Pending, Current)
P0050 - HO2S Heater Control Circuit (Bank 2, Sensor 1) (Pending, Current)
P0056 - HO2S Heater Control Circuit (Bank 2, Sensor 2) (Pending, Current)
P0443 - Evaporative Emission System Purge Control Valve Circuit (Pending, Current)
P0449 - Evaporative Emission System Vent Control Circuit Intermittent (Pending, Current)
P0452 - Evaporative Emission System Pressure Sensor/Switch Low (Pending, Current)
P0740 - Torque Converter Clutch Solenoid Circuit / Open (Pending, Current)
P0785 - Shift/Timing Solenoid (Pending, Current)
P0054 - HO2S Heater Resistance (Bank 1, Sensor 2) (Pending)
P0059 - HO2S Heater Resistance (Bank 2, Sensor 1) (Pending)
P0060 - HO2S Heater Resistance (Bank 2, Sensor 2) (Pending)
You have a lot of codes that need attention.. sepcifically on the o2 issue anything that says sensor 1.
The passenger side sensor looks like it might be shorted to ground or something is off.
Tuner at PCMofnc.com
Email tuning!!!, Mail order, Dyno tuning, Performance Parts, Electric Fan Kits, 4l80e swap harnesses, 6l80 -> 4l80e conversion harnesses, Installs