Ben is 100% on point, PC told me the same thing as well. 1st thing Jannetty Racing had me do is break out the MAP and add the 3 bar MAP into the intake manifold.
Type: Posts; User: Sneakyws6
Ben is 100% on point, PC told me the same thing as well. 1st thing Jannetty Racing had me do is break out the MAP and add the 3 bar MAP into the intake manifold.
Does anyone have any input or suggestions on what changes to the fan logic that should be made after putting a 160? on a 19 Z06?
So I pulled the Soler TB off and put my lightly massaged/ported stock TB back on the car. Drove it for 2 days and then while coming home last night at 60mph I went from 6th to 3rd and rolled the...
As much as I want to use Pray (again) that was the unit that failed, now he is super backed up and months out. I have ported some of my OEM myself and smoother the ridges on the entrance, the data...
I was worried about those cuts as well. You confirmed my hunch, the TB is messing with the off idle to part throttle map way too much. I am going to get with Soler and see if they will take it back.
So my original ported 87mm TB died after almost 4 years, it was a ported unit from a reputable vendor. I replaced it with another 87mm ported TB from Soler performance. The new TB is a nice unit,...
I can tell you for sure, the split pulse tables do affect start up and the 1st 60-90 seconds of run time. I had to fix the tables and put them back to stock when my tuner modified them. He had them...
I am surprised the split pulse it turned off, the table is filled out and it is active on my 17 Camaro SS from the factory.
The exhaust will be loud for the 1st 60-90 seconds. It is caused by the dual pulse timing that is used to help the cats fire off faster.
I have the IAT Advance logged, it sits at 0*. Once I get home later I will post up the tune and the log run.
I am using a 3 bar MAP, a MAP/IAT breakout harness as well. IAT is in the IM just past...
So the other day while logging I noticed I wasnt seeing any changes to the tune from the IAT tables. I have a 17 Camaro SS 1LE with a Procharger D1SC that also has a Alky Controls meth injection...
Not possible with HPT, launch control is controlled by the BCM.
So the car runs great, the only real question I have is in regards to when the engine is no load rev'd or free rev'd. Especially when trying to manually rev match. Mine seems to hang for a bit, like...
The changes for the ZL1 drag update have more to do with how the eLsd locks and unlocks than anything else.
Does anyone know what in the tables controls the rev match? Sometimes it will work fine, but then it will quit working. Trying to help a buddy on his car. I have a 17, he has a 18 but both have the...
What vehicle is this from? carbon fouling or "coking" as they call it is normal on the newer DI GM vehicles.
Its gone, all you can do now is hope someone uploaded a stock file to the HPT tune repository.
It is a normal issue on those engines, the 5.3 and the 6.2 both knock on 91 from the factory. My 2016 6.2/A8 knocks as well. They really need 93 octane, but you can also add some E85 to the 91 mix to...
So question on re-scaling MAF this way. So when I make changes in the airflow zones that need the correction based on the current E ratio I am at, then down the road lets say I put all gas in the...
Low side is at 73psi at 6500rpm, high side is almost 2700psi and injector duty is 5.5ms.
Yes, the car has a FF sensor. Current E is at E35.
I already have a config file built from my GM stuff, when I connected to the most of the sensors grayed out. I re-polled for sensors and got some of them online. Was just wondering if someone had a...
Yes, that helps as well. I found an online conversion table for stoich. If Lambda is commanded at .84 it would give me a 8.2:1 for E85 and 12.35:1 for gas. That means based on the formula you just...
The 14-17 SQ5 is the same vehicle as the Q5, the only changes was some additional fluid coolers and the SQ5 runs a hotter OEM tune.
I will get with support and ask them. You dont need to license...
So I have the GM side of the scanner under control. Now I am needing to scan my wifes 16 Audi SQ5, obviously the GM config doesnt work on the Audi. Does anyone have a config file to use to scan the...