Hey guys! Anyone have a way to connect your wideband to the MPVI2 and see it in VCM Scanner?
Hey guys! Anyone have a way to connect your wideband to the MPVI2 and see it in VCM Scanner?
NO! 2 Weeks!
You can use the AEM wideband that we sell in our online store on most CAN based vehicles, but if you are looking for an analog input solution it is still in development for the MPVI2
It doesn't have to be perfect, it just needs to be done in two weeks...
A wise man once said "google it"
Thanks for the answer Bill, it seems Blue Bee is trying to mislead me
Will the can based wideband work on an 2007 Yukon Denali?
If the OBDII connector, on your vehicle, has the CANH (PIN6) and CANL (PIN14) pins installed, you very likely have a CAN based ECU.
It must have BOTH pins.
ECU-ID.jpg
My 2007 Sky Redline has CAN. So, it does happen. I have not seen it on anything prior to 2006, though. Everything 2008, and later, should be CAN.
One option is to hard wire it into your ECU using the EGR sensor circuit. https://forum.hptuners.com/showthrea...nd-through-EGR
~Erik~
2013 Sonic RS - manual, CGM, 6M, sunroof, mods in process
2008 TrailBlazer 3SS AWD LS2, loaded, dropped, modded, SE22 Performance tuned. And then some...
2002 TrailBlazer LT 4WD 4.2L I6, lifted, tires, exhaust, SE22 Performance tuned
Thanks for the info guys
Ok so If I run the aem x series obd2 wideband with the mpvi2 I should be able to log afr?s on a 2007 srt8 Charger correct? I?ve been debating on trying to find a mpvi for sale so I can log afr?s for my tuner but if it?s possible with the aem and the mpvi2 I?ll go that route.
Last edited by Bull_Market; 08-10-2018 at 02:20 AM.
Which of the above pictures ( from post #6 ) does your car's OBDII connector look like ?
If it looks like the "CAN based ECU" connector, you should be good to go.
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
By all means, share. But, I'm sure somebody can make a better pic than that
I wish I had a solution for the non-CAN guys. But, as soon as I could get it out there, the PRO/HUB thing would be ready.
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
I upgraded to MPVI2 over a year ago, and at that time my LC-1 wideband would work in my scanner. Since then my laptop died, got a new one, and downloaded the new 4.6.0 VCM SUITE. Now my LC-1 will not work with the Scanner, and no one seems to have a solution.
And I am not purchasing the AEM wideband sold by HPTuners just to solve this problem.
Bill, please get this fixed so that I and other users can utilize their widebands with MPVI2. Thanks
2.8/3.0/3.2 Pulley/ZZP CAI/1.6 HS Rockers/Hi Energy Comp Cam 76-802-9/LS7 Lifters/ZZP Stage 2 Intercooler/TOG Headers/Triple Edge Performance Stage 3 Transmission/3.29 Ratio/NGK TR6ix IRIDIUM .40 GAP/ZZP Fuel Rails/ZEX 100 shot NOS/GMPP Sway Bars/KYB Adjustable Struts/Power Stop Performance Pads/Rotors
Pro feature set + MPVI2, been out since 2018 https://forum.hptuners.com/showthrea...ure-Set-Update
It doesn't have to be perfect, it just needs to be done in two weeks...
A wise man once said "google it"